Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P001200  Camshaft Position "A" - Timing Over-Retarded Bank 1  


DESCRIPTION

Refer to DTC P001001.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P001001

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001200 Camshaft Position "A" - Timing Over-Retarded Bank 1 With engine warmed up and while driving in urban area (engine speed 4000 rpm or less), intake side valve timing does not change in retarded position, and target and actual valve timing do not match (1 trip detection logic).
·

Camshaft timing gear assembly

·

Cam timing control motor with EDU assembly

·

ECM


Comes on DTC stored SAE Code: P0012

MONITOR DESCRIPTION

This DTC is output when a valve timing stuck condition is detected. With the engine speed at 4000 rpm or less in the retard angle position, if the valve timing does not vary, and there is a large difference in the target and actual valve timing, it is determined that a malfunction has occurred. When this malfunction is detected, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing gear assembly
Cam timing control motor with EDU assembly
Required Sensors/Components (Related) Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A408761E03
3.594,3.49 3.698,3.49 3.698,3.49 4.146,2.646 false 6.156,3.458 6.26,3.458 6.26,3.458 6.708,2.615 false 0.167,0.323 1.313,0.563 1.146,0.24 10 false Vehicle Speed 0.198,1.125 1.094,1.646 0.896,0.521 10 false Approximately 60 km/h 0.76,2.104 1.677,2.302 0.917,0.198 10 false Idling 0.26,2.302 1.125,3.042 0.865,0.74 10 false Power Switch on (IG) 1.354,2.354 2.271,2.552 0.917,0.198 10 false [A] 2.438,0.073 6.958,0.844 4.521,0.771 10 false *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 1.615,2.75 2.531,2.948 0.917,0.198 10 false Warming up 2.563,2.771 4.302,3.042 1.74,0.271 10 false 10 minutes or more 2.438,3.385 3.708,3.656 1.271,0.271 10 false 3 minutes or more 5,3.365 6.271,3.635 1.271,0.271 10 false 3 minutes or more 1.885,2.021 2.802,2.219 0.917,0.198 10 false [B] 3.01,1.01 3.927,1.208 0.917,0.198 10 false [C] 4.042,2.292 4.958,2.49 0.917,0.198 10 false [D] 4.26,3.167 5.177,3.365 0.917,0.198 10 false [E] 5.438,2.24 6.354,2.438 0.917,0.198 10 false [F]* 6.813,3.156 7.073,3.385 0.26,0.229 10 false [H] 6.594,2.281 6.917,2.531 0.323,0.25 10 false [G] 0.115,1.458 1.156,1.958 1.042,0.5 10 false [Engine running]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

10.

With the engine running, drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

Idle the engine for 3 minutes or more [D].

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P001200.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [F] through [H].



17.

With the engine running, repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

If the engine stops, further depress the accelerator pedal to restart the engine.

·

Depress the accelerator pedal by a large amount.



18.

Idle the engine for 3 minutes or more [G].

19.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

20.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



21.

Check the DTC judgment result again.

HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

The GTS only:

By using the Control the VVT-iE Opening Angle Bank 1 Active Test, it can be determined if the VVT-iE system is malfunctioning.

(a)

Connect the GTS to the DLC3.

(b)

Turn the power switch on (IG).

(c)

Turn the GTS on.

(d)

Clear the DTCs.

(e)

Turn the power switch off and wait for at least 30 seconds.

(f)

Turn the power switch on (IG).

(g)

Turn the GTS on.

(h)

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

(i)

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

(j)

Enter the following menus: Powertrain / Engine / Active Test / Control the VVT-iE Opening Angle Bank 1 / Data List / Intake VVT Change Angle Bank 1 and Intake VVT Target Angle Bank 1.

(k)

Read the Data List while performing the Active Test with the engine idling.

OK:
Active Test Movement Order Difference between "Intake VVT Change Angle Bank 1" and "Intake VVT Target Angle Bank 1"
0 deg → 10 deg → 20 deg → 40 deg → 0 deg → 10 deg → END Within 4 DegFR


·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001200)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001200 is output A
DTC P001200 and other DTCs are output B


HINT:

If any DTCs other than P001200 are output, troubleshoot those DTCs first.




A

2.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

B

2.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
A402065C03
0.625,1.333 1.344,1.188 true 0.458,1.229 0.771,1.427 0.313,0.198 10 false *2 0.177,0.073 0.49,0.271 0.313,0.198 10 false *1
*1 Camshaft Timing Gear Assembly
*2 Eccentric Shaft


a.

Remove the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>CAMSHAFT TIMING CONTROL MOTOR>REMOVAL


b.

Check if the eccentric shaft of the camshaft timing gear assembly rotates smoothly.

NOTICE:

If the camshaft is at a position where a valve is about to open, the eccentric shaft may become difficult to rotate.


OK:

Rotates smoothly.



HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly, or removing the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

3.REPLACE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

3.REPLACE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY
a.

Replace the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>CAMSHAFT TIMING CONTROL MOTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001200 is output B




A

END

B