Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P03652A  Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range  P036531  Camshaft Position Sensor "B" Bank 1 No Signal  


DESCRIPTION

Refer to DTC P036511.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P036511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P03652A Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range No camshaft position sensor (for exhaust camshaft) signal to ECM while engine cranking (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

Exhaust camshaft

·

ECM


Comes on DTC stored SAE Code: P0365
P036531 Camshaft Position Sensor "B" Bank 1 No Signal No camshaft position sensor (for exhaust camshaft) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

Exhaust camshaft

·

ECM


Comes on DTC stored SAE Code: P0365

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P034011

MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor (for exhaust camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine [A].

10.

Idle the engine for 10 seconds or more [B].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P03652A or P036531.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A402448C96
0.26,1.104 0.667,1.354 0.406,0.25 0.76,1.833 1.365,1.458 false 2.76,1.833 2.021,1.458 false 1.74,1.958 1.74,1.469 false 0.208,0.167 0.583,0.438 0.375,0.271 10 false *a 0.344,1.146 0.719,1.417 0.375,0.271 10 false C12 0.354,1.76 1,2.073 0.646,0.313 10 false VVE+ 2.823,1.781 3.198,2.052 0.375,0.271 10 false VC2 1.625,1.979 2.26,2.156 0.635,0.177 10 false VVE-
*a Front view of wire harness connector
(to Camshaft Position Sensor (for Exhaust Camshaft))


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C12-3 (VC2) - Body ground Power switch on (IG) 4.5 to 5.5 V
C12-1 (VVE+) - Body ground Power switch on (IG) 3.0 to 5.0 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-3 (VC2) - C12-1 (VVE+) Power switch off 1.425 to 1.575 kΩ
C12-2 (VVE-) - Body ground Power switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

NG

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
2.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


a.

Visually check the camshaft position sensor (for exhaust camshaft) for damage.


b.

Check the camshaft position sensor (for exhaust camshaft) installation condition.

OK:

The camshaft position sensor (for exhaust camshaft) does not have any damage and is installed properly.



Result:
Proceed to
OK
NG



OK

3.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

3.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.



HINT:

Perform "Inspection After Repair" after replacing the exhaust camshaft.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

NG

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-1 (VVE+) - C45-91 (EV1+) Always Below 1 Ω
C12-2 (VVE-) - C45-114 (EV1-) Always Below 1 Ω
C12-3 (VC2) - C45-113 (VCE1) Always Below 1 Ω
C12-1 (VVE+) or C45-91 (EV1+) - Body ground and other terminals Always 10 kΩ or higher
C12-2 (VVE-) or C45-114 (EV1-) - Body ground and other terminals Always 10 kΩ or higher
C12-3 (VC2) or C45-113 (VCE1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR