Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P052012  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery  P052014  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open  


DESCRIPTION

A107720E49
0.135,0.708 1.406,1 1.271,0.292 10 false Voltage (V) 0.344,1.031 0.573,1.24 0.229,0.208 10 false 4.5 0.333,2.156 0.563,2.365 0.229,0.208 10 false 0.5 0.74,2.417 0.854,2.625 0.115,0.208 10 false 0 2.542,2.417 2.948,2.688 0.406,0.271 10 false 1.0 1.198,2.688 2.615,2.927 1.417,0.24 10 false Oil Pressure (MPa) 0.427,0.177 3.01,0.646 2.583,0.469 10 false Characteristics of Oil Pressure Sensor:

Variable oil pump control uses the oil pressure control valve assembly, engine oil temperature sensor, oil pressure sensor and ECM to optimize the oil pressure and oil volume required by each component to reduce friction by monitoring the engine temperature and engine speed. The oil pressure sensor utilizes a semiconductor type pressure sensor that changes resistance in accordance with changes in pressure. An internal electrical signal that varies with the change in resistance is amplified and sent to the ECM as the engine oil pressure signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P052012 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery The oil pressure sensor output voltage is higher than 4.78 V for 5 seconds or more (1 trip detection logic).
·

Open or short in oil pressure sensor (oil pressure and temperature sensor) circuit

·

Oil pressure sensor (oil pressure and temperature sensor)

·

ECM


Comes on DTC stored SAE Code: P0523
P052014 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open The oil pressure sensor output voltage is less than 0.23 V for 5 seconds or more (1 trip detection logic).
·

Open or short in oil pressure sensor (oil pressure and temperature sensor) circuit

·

Oil pressure sensor (oil pressure and temperature sensor)

·

ECM


Comes on DTC stored SAE Code: P0522

Related Data List
DTC No. Data List
P052012 Engine Oil Pressure
P052014

MONITOR DESCRIPTION

The ECM calculates the engine oil pressure based on the output voltage of the oil pressure sensor (oil pressure and temperature Sensor). If the signal output from the oil pressure sensor is outside of the specified range, the MIL is illuminated and a DTC is stored.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Wait 10 seconds or more [B].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P052012 or P052014.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions




HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [A] through [C] again.



WIRING DIAGRAM

A402979E26
1.021,1.719 1.552,1.927 0.531,0.208 10 false POUT 1.198,1.031 1.729,1.24 0.531,0.208 10 false VC 1.115,2.5 1.646,2.708 0.531,0.208 10 false GND 4.75,0.938 5.281,1.146 0.531,0.208 10 false VCPE 4.479,0.938 5.01,1.146 0.531,0.208 10 false 99 4.417,2.396 4.948,2.604 0.531,0.208 10 false 100 4.417,1.625 4.948,1.833 0.531,0.208 10 false 122 4.927,2.125 5.458,2.333 0.531,0.208 10 false 200 kΩ 4.75,2.594 5.281,2.802 0.531,0.208 10 false EPEO 4.75,1.625 5.281,1.833 0.531,0.208 10 false PEO 5.854,3.115 6.385,3.323 0.531,0.208 10 false ECM 5.094,3.115 5.625,3.323 0.531,0.208 10 false C45 0.24,2.896 0.771,3.104 0.531,0.208 10 false C5 0.229,3.063 4.521,3.552 4.292,0.49 10 false Oil Pressure Sensor (Oil Pressure and Temperature Sensor) 1.5,0.927 2.031,1.135 0.531,0.208 10 false 3 1.5,2.385 2.031,2.594 0.531,0.208 10 false 2 1.49,1.604 2.021,1.813 0.531,0.208 10 false 1 6.115,0.688 6.646,0.896 0.531,0.208 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A373523C64
0.302,1.052 0.719,1.302 0.417,0.25 0.875,1.604 1.292,1.188 true 1.417,1.781 1.573,1.208 true 2.188,1.74 1.802,1.208 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 0.417,1.094 0.729,1.292 0.313,0.198 10 false C5 0.646,1.615 1.146,1.802 0.5,0.188 10 false POUT 1.271,1.802 1.646,2.042 0.375,0.24 10 false GND 2.135,1.76 2.448,1.958 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Oil Pressure Sensor (Engine Oil Pressure and Temperature Sensor))


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the oil pressure sensor (oil pressure and temperature sensor) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C5-3 (VC) - Body ground Power switch on (IG) 4.5 to 5.5 V
C5-1 (POUT) - Body ground Power switch on (IG) Below 0.1 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-1 (POUT) - C5-2 (GND) Power switch off 190 to 210 kΩ
C5-2 (GND) - Body ground Power switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OIL PRESSURE SENSOR (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SENSOR (OIL PRESSURE AND TEMPERATURE SENSOR) - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SENSOR (OIL PRESSURE AND TEMPERATURE SENSOR) - ECM)
a.

Disconnect the oil pressure sensor (oil pressure and temperature sensor) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-2 (GND) - C45-100 (EPEO) Always Below 1 Ω
C5-1 (POUT) - C45-122 (PEO) Always Below 1 Ω
C5-3 (VC) - C45-99 (VCPE) Always Below 1 Ω
C5-2 (GND) or C45-100 (EPEO) - Body ground and other terminals Always 10 kΩ or higher
C5-1 (POUT) or C45-122 (PEO) - Body ground and other terminals Always 10 kΩ or higher
C5-3 (VC) or C45-99 (VCPE) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR