Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P059712  Thermostat Heater Control Circuit Short to Battery  


DESCRIPTION

An electric heater is equipped to the temperature sensing portion of the thermostat. During normal driving, current does not flow to the heater and the thermostat functions as an ordinary thermostat. When the temperature of the engine increases by a large amount such as during high-load driving, control is performed to warm the heater of the temperature sensing portion, forcing the valve to open and causing a large amount of coolant to flow from the radiator.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P059712 Thermostat Heater Control Circuit Short to Battery Short in thermostat heater circuit and power supply circuit (1 trip detection logic).
·

Short in thermostat heater circuit

·

ECM


Comes on DTC stored SAE Code: P0599

Related Data List
DTC No. Data List
P059712 Coolant Temperature

MONITOR DESCRIPTION

The ECM monitors the output voltage while the thermostat heater is operating.

The thermostat heater turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the thermostat heater circuit and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A232052E55
0.438,0.031 3.292,0.333 2.854,0.302 10 false Coolant Temperature: 90°C or higher 0.792,0.479 1.844,0.75 1.052,0.271 10 false Calculate Load 1.563,0.885 2.375,1.271 0.813,0.385 10 false 45% 1.417,2.031 1.833,2.281 0.417,0.25 10 false Idling 0.552,2.365 2,2.635 1.448,0.271 10 false Power Switch on (IG) 2.938,1.854 3.198,2.094 0.26,0.24 10 false [A] 4.813,0.406 5.115,0.635 0.302,0.229 10 false [B] 6.229,3.229 6.531,3.479 0.302,0.25 10 false [C] 4.229,3 5.531,3.281 1.302,0.281 10 false 3 seconds or more 0.865,1.063 1.896,1.406 1.031,0.344 10 false [Engine running]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

10.

Enter the following menus: Powertrain / Engine / Data List / Calculate Load and Coolant Temperature.

11.

With the engine running, drive the vehicle for at least 3 seconds at the Calculate Load of 45% or more and the Coolant Temperature of 90°C (194°F) or higher [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


12.

Stop the vehicle.

13.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P059712.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A409165E09
0.583,3.833 3.188,4.031 2.604,0.198 10 false Auxiliary Battery 0.458,3.094 3.063,3.292 2.604,0.198 10 false MAIN 0.49,2.74 1.667,2.979 1.177,0.24 10 false EFI-MAIN NO. 1 0.469,1.667 1.104,2.042 0.635,0.375 10 false EFI-MAIN NO. 2 1.521,1.948 2.573,2.208 1.052,0.26 10 false EFI-MAIN NO. 2 2.688,1.333 3.74,1.594 1.052,0.26 10 false EFI2 NO. 2 1.51,3.365 2.688,3.604 1.177,0.24 10 false EFI-MAIN NO. 1 3.583,1.406 4.635,1.667 1.052,0.26 10 false F5 3.583,1.563 5.531,2.115 1.948,0.552 10 false Thermostat Heater (Water Inlet with Thermostat Sub-assembly) 3.771,1.083 4.198,1.26 0.427,0.177 10 false 1 5.052,1.083 5.479,1.26 0.427,0.177 10 false 2 5.292,1.188 5.75,1.354 0.458,0.167 10 false C45 5.292,3.094 5.75,3.26 0.458,0.167 10 false A24 5.385,1 5.844,1.167 0.458,0.167 10 false 7 5.344,2.906 5.802,3.073 0.458,0.167 10 false 15 5.667,1.188 6.125,1.354 0.458,0.167 10 false HTHM 5.677,3 6.135,3.167 0.458,0.167 10 false MREL 6.031,4.188 6.49,4.354 0.458,0.167 10 false ECM 6.417,3.094 6.698,3.333 0.281,0.24 10 false IC 1.583,1.583 2.01,1.76 0.427,0.177 10 false 1 2.281,1.583 2.708,1.76 0.427,0.177 10 false 2 2.292,1.083 2.719,1.26 0.427,0.177 10 false 5 1.594,1.083 2.021,1.26 0.427,0.177 10 false 3 1.615,2.979 2.042,3.156 0.427,0.177 10 false 1 2.292,2.979 2.719,3.156 0.427,0.177 10 false 2 2.302,2.479 2.729,2.656 0.427,0.177 10 false 5 1.604,2.49 2.031,2.667 0.427,0.177 10 false 3 3.948,1.073 4.49,1.323 0.542,0.25 10 false ETM+ 4.635,1.073 5.177,1.323 0.542,0.25 10 false ETM-

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THERMOSTAT HEATER (WATER INLET WITH THERMOSTAT SUB-ASSEMBLY) - ECM)
a.

Disconnect the thermostat heater (water inlet with thermostat sub-assembly) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F5-2 (ETM-) or C45-7 (HTHM) - other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR