Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P062F44  Internal Control Module EEPROM Data Memory Failure  


DESCRIPTION

The ECM monitors its internal operation and stores this DTC when it detects an internal malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P062F44 Internal Control Module EEPROM Data Memory Failure An ECM internal error (EEPROM) (1 trip detection logic). ECM Comes on DTC stored SAE Code: P062F

MONITOR DESCRIPTION

The ECM monitors its internal operation. If the internal operation is malfunctioning, the ECM illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous: Case 1, Case 2
Once per driving cycle: Case 3

TYPICAL ENABLING CONDITIONS

Case 1
All of the following conditions are met -
Fault Code Not stored
OBDII system commands Store
Auxiliary battery voltage 8 V or higher

Case 2
All of the following conditions are met -
Fault Code Stored
OBDII system commands Clear
Auxiliary battery voltage 8 V or higher

Case 3
Auxiliary battery voltage 8 V or higher

TYPICAL MALFUNCTION THRESHOLDS

Case 1
The following condition is met 2 data or more
One of the following conditions (a), (b) or (c) is met More than 3 times
(a) EEPROM communication timeout Occurred
(b) Fault Code Not stored
(c) Fault Code Not equal to commanded Fault Code

Case 2
The following condition is met 2 data or more
Either of the following conditions (a) or (b) is met More than 3 times
(a) EEPROM communication timeout Occurred
(b) Fault Code Stored

Case 3
Either of the following conditions is met 1 or 2
1. The following condition is met 2 data or more
EEPROM communication timeout (more than 3 times) Occurred
2. Fault Code data (more than 10 times) Mismatch

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the GTS off.

6.

Turn the power switch off.

7.

Disconnect the GTS.

8.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

9.

Connect the cable to the negative (-) auxiliary battery terminal.

10.

Connect the GTS to the DLC3.

11.

Start the engine and wait 30 seconds or more.

12.

Turn the GTS on.

13.

Enter the following menus: Powertrain / Engine / Trouble Codes.

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P062F44.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

NOTICE:
·

After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P062F44)
2.READ OUTPUT DTC (DTC P062F44)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Connect the GTS to the DLC3.


d.

Start the engine and wait 30 seconds or more.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P062F44 is output B




A

B