Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P044313  Evaporative Emission System Purge Control Valve "A" Circuit Open  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of evaporated fuel routed to the cylinders is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P044313 Evaporative Emission System Purge Control Valve "A" Circuit Open Both of the following conditions are met (1 trip detection logic):
·

The purge VSV operation duty signal is 5 to 95%.

·

The target control value and actual control value do not match for 10 seconds or more.


·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored SAE Code: P0443

CONFIRMATION DRIVING PATTERN

A179391E66
4.156,1.563 3.76,0.615 3.76,0.615 3.865,0.615 false 1.521,1.948 1.75,2.125 0.229,0.177 10 false [A] 2.844,1.948 3.073,2.125 0.229,0.177 10 false [B] 3.896,3.01 4.125,3.188 0.229,0.177 10 false [C] 4.573,1.333 4.802,1.51 0.229,0.177 10 false [D] 5.094,3.021 5.323,3.198 0.229,0.177 10 false [E] 0.51,2.073 0.885,2.26 0.375,0.188 10 false Idling 4.229,2.604 5.01,2.917 0.781,0.313 10 false 10 minutes or more 2.594,2.583 3.375,2.896 0.781,0.313 10 false 15 minutes or more 1.292,2.583 2.083,2.75 0.792,0.167 10 false Warming up 3.958,0.542 6.594,0.792 2.635,0.25 10 false Between 40 and 60 km/h [Engine running] 0.125,0.375 1.073,0.542 0.948,0.167 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessories should be off.


10.

Idle the engine for 15 minutes or more [B].

HINT:

Check the Data List item "EVAP (Purge) VSV". When the value of this item is between 5 and 95%, the judgment will be performed.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P044313.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system is malfunctioning.

·

If the judgment result shows INCOMPLETE, perform steps [D] and [E].



16.

With the engine running, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


17.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

18.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



19.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

20.

Input the DTC: P044313.

21.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A413271E08
0.563,3.823 3.167,4.021 2.604,0.198 10 false Auxiliary Battery 0.469,1.677 1.115,2.083 0.646,0.406 10 false EFI-MAIN NO.1 1.531,1.938 3.521,2.135 1.99,0.198 10 false EFI-MAIN NO.1 0.458,3.115 1.073,3.313 0.615,0.198 10 false MAIN 2.385,1.313 3.615,1.51 1.229,0.198 10 false EFI NO.1 6.469,3.073 6.781,3.271 0.313,0.198 10 false IC 5.646,1.177 6.104,1.375 0.458,0.198 10 false PRG 5.646,3 6.26,3.198 0.615,0.198 10 false MREL 2.25,1.573 2.406,1.771 0.156,0.198 10 false 2 5.042,1.083 5.198,1.281 0.156,0.198 10 false 2 3.813,1.094 3.969,1.292 0.156,0.198 10 false 1 1.604,1.583 1.76,1.781 0.156,0.198 10 false 1 1.604,1.083 1.76,1.281 0.156,0.198 10 false 3 2.25,1.083 2.406,1.281 0.156,0.198 10 false 5 3.969,1.656 5.344,1.854 1.375,0.198 10 false Purge VSV 3.969,1.51 4.427,1.708 0.458,0.198 10 false C19 5.313,1 5.625,1.198 0.313,0.198 10 false 66 5.313,2.896 5.625,3.094 0.313,0.198 10 false 15 5.271,1.177 5.885,1.375 0.615,0.198 10 false C45 5.271,3.083 5.885,3.281 0.615,0.198 10 false A24 6.031,4.177 6.49,4.375 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EVAP PURGE VSV)
A407293

a.

Disconnect the fuel vapor feed hose assembly (canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1

h.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction your finger.

OK:
GTS Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV
a.

Inspect the purge VSV.

Click hereEngine / Hybrid System>A25A-FXS (EMISSION CONTROL)>PURGE VALVE>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
A376495C45
0.302,1.073 0.688,1.354 0.385,0.281 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 0.385,1.135 0.844,1.333 0.458,0.198 10 false C19
*a Front view of wire harness connector
(to Purge VSV)


a.

Disconnect the purge VSV connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C19-1 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - PURGE VSV)

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C19-2 - C45-66 (PRG) Always Below 1 Ω
C19-2 or C45-66 (PRG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR