Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0372747 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  C1AAE00  Front Recognition Camera Heater Malfunction  


DESCRIPTION

The forward recognition camera controls the current to the forward recognition hood with heater sub-assembly.

C1AAE00 is stored when the forward recognition camera detects a forward recognition hood with heater sub-assembly operation circuit malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAE00 Front Recognition Camera Heater Malfunction When 10 seconds elapse after turning the ignition switch to ON, the forward recognition camera determines that one of the following conditions is met
·

Short to +B in the hot wire circuit accumulated for 1 second or more

·

Open or short to ground in the hot wire circuit continued for 5 seconds or more


·

Forward recognition with heater hood sub-assembly

·

Forward recognition camera

·

Harness or connector



DTC detection condition combination table: C1AAE00
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Detection condition 10 seconds elapse after turning the ignition switch to ON ○ ○ ○
Malfunction status Short to +B in hot wire circuit ○ - -
Open circuit in hot wire circuit - ○ -
Short to GND in hot wire circuit - - ○
Malfunction duration 1 second or more continuously 5 seconds or more continuously 5 seconds or more continuously
Number of trips 1 trip 1 trip 1 trip

HINT:

The DTC is output when a combination of any of the above conditions are met.


WIRING DIAGRAM

E402453E08
2.563,1.063 4.396,1.26 1.833,0.198 10 false ECU-IG1 NO.3 5.802,0.833 6.323,1.135 0.521,0.302 10 false HTR 5.625,1.802 6.927,2.146 1.302,0.344 10 false P8 5.625,1.958 6.927,2.302 1.302,0.344 10 false Forward Recognition Camera 4.885,0.771 5.406,1.073 0.521,0.302 10 false HTR 3.938,0.781 4.458,1.083 0.521,0.302 10 false IG1 5.573,0.76 6.094,1.063 0.521,0.302 10 false 1 5.25,0.76 5.771,1.063 0.521,0.302 10 false 2 3.74,0.781 4.26,1.083 0.521,0.302 10 false 1 0.896,0.813 2.521,1.219 1.625,0.406 10 false from IG1 NO.1 Relay 3.635,1.167 4.083,1.427 0.448,0.26 10 false P17 3.646,1.323 5.635,1.74 1.99,0.417 10 false Forward Recognition with Heater Hood Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)




PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 430

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Recheck for DTCs and check that no DTCs are output.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 430
OK:

DTC C1AAE00 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
2.CHECK FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
a.
A401973C38
1.688,1.854 1.823,1.26 true 2.188,1.854 2.042,1.271 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.563,1.885 2.021,2.083 0.458,0.198 10 false HTR 2.135,1.885 2.594,2.083 0.458,0.198 10 false IG1
*a Component without harness connected
(Forward Recognition with Heater Hood Sub-assembly)


Turn the ignition switch off.


b.

Disconnect the P17 forward recognition with heater hood sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (IG1) - 2 (HTR) Ignition switch off 28.5 to 31.5 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - BATTERY)

NG

REPLACE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - BATTERY)
a.
A401974C51
1.552,0.208 1.938,0.448 0.385,0.24 0.979,1.604 1.188,1.604 1.188,1.604 1.583,1.271 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.625,0.24 2.083,0.438 0.458,0.198 10 false P17 0.677,1.469 1.135,1.667 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Forward Recognition with Heater Hood Sub-assembly)


Disconnect the forward recognition with heater hood sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P17-1 (IG1) - Body ground Ignition switch ON 8 to 16 V
Ignition switch off Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the P17 forward recognition with heater hood sub-assembly connector.


b.

Disconnect the P8 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P17-2 (HTR) - P8-1 (HTR) Always Below 1 Ω
P17-2 (HTR) or P8-1 (HTR) - Body ground Always 10 kΩ or higher



d.

Reconnect the P8 forward recognition camera connector.


e.

Reconnect the P17 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR