Home › Drivetrain › EG62F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076271 EG62F MANUAL TRANSMISSION / TRANSAXLE _0372179 MANUAL TRANSAXLE SYSTEM U

EG62F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

-

There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the Freeze Frame Data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.



Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
600 to 700 rpm: Engine idling (shift lever in neutral, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Mass Air Flow Sensor Airflow rate from mass air flow meter sub-assembly Min.: 0 gm/sec
Max.: 655.35 gm/sec
·

1.5 to 3.3 gm/sec: Engine idling (engine warmed up)

·

8.0 to 13.0 gm/sec: 3000 rpm (without load)


This is the intake air amount measured by the mass air flow meter sub-assembly.
Intake Manifold Absolute Pressure Intake manifold absolute pressure Min.: 0 kPa (0 psi)
Max.: 2047.96 kPa (296.95 psi)
·

80 to 110 kPa (11.6 to 15.95 psi): Ignition switch ON

·

18 to 38 kPa (2.6 to 5.5 psi): Engine idling with warmed up engine


·

This is the intake manifold pressure.

·

This item is the pressure detected by the manifold absolute pressure sensor and is used for air fuel ratio control and EGR valve control.


HINT:

When the ignition switch is ON, the manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa(abs) [14.65 psi(abs)]).


Intake Manifold Absolute Pressure Supported Status of intake manifold absolute pressure Unsupp or Supp Supp -
Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F)
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up
HINT:
·

After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.

·

Check if the engine overheats if the value indicated is higher than 135°C (275°F).



Throttle Motor Duty Ratio Throttle actuator Min.: 0%
Max.: 100%
0 to 22%: Engine idling with warmed up engine (A/C off and shift lever in neutral) This is the output duty ratio of the throttle actuator drive circuit.
Starter SW Starter signal ON or OFF
·

ON: Starter operating

·

OFF: Starter not operating


-
Stop Light SW Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
NIM Sensor Speed Input shaft speed (NIM) Min.: 0 rpm
Max.: 16383 rpm
Equal to engine speed (NE): Clutch pedal not depressed, vehicle being driven -
NIM Sensor Voltage Input shaft speed (NIM) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Clutch pedal not depressed, vehicle being driven -
Shift SW Status (R Range) Back-up light switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


-
Shift SW Status (N,P Range) Clutch pedal switch status ON or OFF
·

ON: Clutch pedal fully depressed

·

OFF: Clutch pedal released


-
Shift SW Status (N,P Range) Supported Status of clutch pedal switch supported Unsupp or Supp Supp -
Clutch Stroke Position Clutch pedal stroke calculated by ECM Min.: -200.0%
Max.: 199.9%
Value increases: Clutch pedal released → clutch pedal fully depressed -
Clutch Stroke Sensor Voltage Clutch pedal stroke sensor assembly output voltage Min.: 0.000 V
Max.: 4.999 V
·

0.96 to 1.04 V: Clutch pedal fully released

·

Value changes progressively (Only increase): Not depressed → Fully depressed (Clutch pedal should be operated slowly)


-
iMT SW iMT switch (integration control and panel assembly) status ON or OFF
·

ON: iMT switch (integration control and panel assembly) being pushed

·

OFF: iMT switch (integration control and panel assembly) not being pushed


-
iMT Telltale iMT telltale display request OFF, Green or Yellow
·

OFF: iMT system off

·

Green: iMT system in standby

·

Yellow: iMT system malfunction, indicator light initial check


-