Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3620E _51 Engine / Hybrid System _076384 M20A-FKS ENGINE CONTROL _0372800 SFI SYSTEM C

M20A-FKS ENGINE CONTROL  SFI SYSTEM  P071512  Input/Turbine Speed Sensor "A" Circuit Short to Battery  P071514  Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open  


DESCRIPTION

The transmission revolution sensor (NIM) system uses a gear attached to the input shaft and a Hall IC type sensor.

The Hall IC built into the transmission revolution sensor (NIM) detects the change in magnetic flux density caused by the rotation of the input shaft gear and outputs a voltage signal representing the input shaft speed to the ECM.

HINT:

In this troubleshooting procedure Input/Turbine Speed Sensor may be used in place of Input Speed Sensor (transmission revolution sensor (NIM)).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071512 Input/Turbine Speed Sensor "A" Circuit Short to Battery The transmission revolution sensor (NIM) output voltage is higher than 1.8 V for 5 seconds or more (1 trip detection logic).
·

Open or short in transmission revolution sensor (NIM) circuit

·

Transmission revolution sensor (NIM)

·

ECM


Comes on DTC stored SAE: P07C0
P071514 Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open The transmission revolution sensor (NIM) output voltage is less than 0.2 V for 5 seconds or more (1 trip detection logic).
·

Open or short in transmission revolution sensor (NIM) circuit

·

Transmission revolution sensor (NIM)

·

ECM


Comes on DTC stored SAE: P07BF

A429907E02
0.271,0.125 1.188,0.323 0.917,0.198 10 false 1 V/DIV. 1.594,1.917 2.823,2.115 1.229,0.198 10 false 2 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:

The correct waveform is as shown.


ECM Terminal Name Between NIMO and E1
Tester Range 1 V/DIV., 2 ms./DIV.
Condition Engine idling and clutch pedal fully released


MONITOR DESCRIPTION

When the ignition switch to ON and the transmission revolution sensor (NIM) output voltage is less than 0.2 V or more than 1.8 V for 5 seconds or more, the ECM stores a DTC and illuminates the MIL.

MONITOR STRATEGY

Required Sensors/Components (Main) Transmission revolution sensor (NIM)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P071512 or P071514.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A427591E04
2.698,1.167 3.156,1.365 0.458,0.198 10 false NMB 2.688,2.281 3.146,2.479 0.458,0.198 10 false NMO 3.125,1.156 3.281,1.354 0.156,0.198 10 false 2 3.115,2.281 3.271,2.479 0.156,0.198 10 false 1 4.885,1.156 5.198,1.354 0.313,0.198 10 false 64 4.885,2.281 5.198,2.479 0.313,0.198 10 false 65 5.115,1.156 5.729,1.354 0.615,0.198 10 false NIMB 5.115,2.281 5.729,2.479 0.615,0.198 10 false NIMO 5.385,3.208 5.917,3.51 0.531,0.302 10 false C40 5.396,3.365 5.854,3.563 0.458,0.198 10 false ECM 0.615,2.927 1.229,3.125 0.615,0.198 10 false C6 0.615,3.083 3.104,3.344 2.49,0.26 10 false Transmission Revolution Sensor (NIM) 5.74,0.958 6.354,1.156 0.615,0.198 10 false 12 V 5.198,2.583 5.969,2.781 0.771,0.198 10 false 100 Ω

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (NIM SENSOR SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and NIM Sensor Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
NIM Sensor Speed
50003 372 211,539

e.

Start the engine.


f.

With the shift lever in neutral and the clutch pedal released, idle the engine and read the tester display.

Standard:
GTS Display Condition Specified Condition
NIM Sensor Speed
·

Engine idling

·

Shift position: Neutral

·

Clutch pedal depressed (clutch engaged)


The value of the Data List item changes in accordance with the engine speed


HINT:
·

If the NIM sensor speed and engine speed match, the transmission revolution sensor (NIM) is operating correctly.

·

If the NIM sensor speed is 0 rpm even when the engine is running, it is possible that there is an open or short in the transmission revolution sensor (NIM) circuit.




Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
A402432C72
0.323,1.073 0.76,1.302 0.438,0.229 0.885,1.75 1.521,1.354 true 2.49,1.781 1.885,1.365 true 0.448,1.115 1.063,1.313 0.615,0.198 10 false C6 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.708,1.823 1.167,2.021 0.458,0.198 10 false NMO 2.375,1.823 2.833,2.021 0.458,0.198 10 false NMB
*a Front view of wire harness connector
(to Transmission Revolution Sensor (NIM))


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the transmission revolution sensor (NIM) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C6-2 (NMB) - Body ground Ignition switch ON 11 to 14 V
C6-1 (NMO) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-1 (NMO) - Body ground Ignition switch off 95 to 105 Ω



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIM) - ECM)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIM) - ECM)
a.

Disconnect the transmission revolution sensor (NIM) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-2 (NMB) - C40-64 (NIMB) Always Below 1 Ω
C6-1 (NMO) - C40-65 (NIMO) Always Below 1 Ω
C6-2 (NMB) or C40-64 (NIMB) - Body ground and other terminals Always 10 kΩ or higher
C6-1 (NMO) or C40-65 (NIMO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR