Home › Vehicle Interior › POWER OUTLETS (INT) › WIRELESS CHARGING SYSTEM
RM3620E _58 Vehicle Interior _076279 POWER OUTLETS (INT) _0371450 WIRELESS CHARGING SYSTEM J

POWER OUTLETS (INT)  WIRELESS CHARGING SYSTEM  Wireless Charger Power Source Circuit  


DESCRIPTION

This is the power source circuit for the mobile wireless charger cradle assembly.

WIRING DIAGRAM

E409569E01
0.406,0.74 1.813,0.927 1.406,0.188 10 false from Auxiliary Battery 0.74,1.406 1.802,1.635 1.063,0.229 10 false from ACC Relay 2.479,0.948 3.531,1.156 1.052,0.208 10 false ECU-DCC NO.2 2.708,1.604 3.458,1.823 0.75,0.219 10 false ECU-ACC 4.198,0.615 4.354,0.813 0.156,0.198 10 false 6 4.198,1.292 4.354,1.49 0.156,0.198 10 false 5 4.208,2.427 4.365,2.625 0.156,0.198 10 false 1 4.188,2.021 4.344,2.219 0.156,0.198 10 false 8* 4.438,0.74 4.75,0.938 0.313,0.198 10 false B+ 4.438,1.292 4.896,1.49 0.458,0.198 10 false ACC 4.458,2.552 5.073,2.75 0.615,0.198 10 false PGND 4.438,2.125 5.052,2.323 0.615,0.198 10 false SDET* 4.177,3.063 4.635,3.26 0.458,0.198 10 false G13 4.177,3.26 6.854,3.5 2.677,0.24 10 false Mobile Wireless Charger Cradle Assembly 5.823,1.417 6.135,1.615 0.313,0.198 10 false IC 0.26,3.292 2.125,3.542 1.865,0.25 10 false *: w/o Light Control Rheostat

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOBILE WIRELESS CHARGER CRADLE ASSEMBLY POWER SOURCE)
a.
E410400C01
1.5,0.156 1.906,0.417 0.406,0.26 0.573,0.917 0.823,0.917 0.823,0.917 1.208,1.25 true 0.813,1.885 1.063,1.885 1.063,1.885 1.417,1.531 true 2.729,1.5 2.521,1.5 2.521,1.5 2.219,1.25 true 2.698,0.729 2.49,0.729 2.49,0.729 1.99,1.24 true 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 1.573,0.198 2.031,0.396 0.458,0.198 10 false G13 0.094,0.833 0.708,1.031 0.615,0.198 10 false PGND 0.115,1.802 0.583,2.042 0.469,0.24 10 false SDET 2.844,1.417 3.156,1.615 0.313,0.198 10 false +B 2.813,0.625 3.271,0.823 0.458,0.198 10 false ACC 0.521,1.792 1.135,1.99 0.615,0.198 10 false (*A)
*A w/o Light Control Rheostat
*a Front view of wire harness connector
(to Mobile Wireless Charger Cradle Assembly)


Disconnect the mobile wireless charger cradle assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/o Light Control Rheostat

G13-1 (PGND) - Body ground Always Below 1 Ω
G13-8 (SDET) - Body ground* Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G13-6 (B+) - Body ground Ignition switch off 11 to 14 V
G13-5 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR