Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › THROTTLE BODY
RM3620E _51 Engine / Hybrid System _076382 A25A-FKS ENGINE CONTROL _0373070 THROTTLE BODY A

A25A-FKS ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.



PROCEDURE

Hide 22030 1.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.



a.
A434401C01
1.219,0.792 0.906,0.25 0.906,0.25 2,0.688 true 0.74,0.115 0.906,0.292 0.167,0.177 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake manifold with the protrusions of the throttle body gasket oriented as shown in the illustration.


b.
A432628C01
2.813,1.74 2.813,1.448 true 2.583,0.885 2.802,1.083 0.219,0.198 10 false *c 3.156,1.073 3.354,1.26 0.198,0.188 10 false *a 3.229,1.313 3.406,1.542 0.177,0.229 10 false *b 3.146,1.563 3.406,1.771 0.26,0.208 10 false *a 2.74,1.76 2.969,1.958 0.229,0.198 10 false *d
*a 45° (Claw of Clip Location)
*b Left of Vehicle
*c Rear of Vehicle
*d Paint Mark


Connect the No. 5 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:
·

If the throttle body with motor assembly has been struck or dropped, replace it.

·

Make sure to position the clip as shown in the illustration.




c.
A432629C01
2.781,1.438 3,1.021 3,1.021 3.167,1.021 true 2.583,0.813 2.792,1.052 0.208,0.24 10 false *a 3.167,1.51 3.365,1.698 0.198,0.188 10 false *c 3.229,1.25 3.406,1.438 0.177,0.188 10 false *b 2.854,1.792 3.01,1.948 0.156,0.156 10 false *c 3.198,0.938 3.406,1.167 0.208,0.229 10 false *d
*a Top
*b Rear of Vehicle
*c 45° (Claw of Clip Location)
*d Paint Mark


Install the throttle body with motor assembly to the intake manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the No. 6 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



e.

Connect the throttle body with motor assembly connector.


Hide 2.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A432630C01
0.479,3.833 0.729,3.365 0.729,3.365 0.896,3.365 true 0.99,4.229 0.99,4.031 0.99,4.031 1.115,3.906 true 0.948,3.271 1.167,3.458 0.219,0.188 10 false *a 0.927,4.26 1.135,4.417 0.208,0.156 10 false *b 2.844,2.99 3.021,3.208 0.177,0.219 10 false *c 2.01,3.927 2.208,4.104 0.198,0.177 10 false *d 1.052,0.24 1.302,0.427 0.25,0.188 10 false *e 2.083,0.25 2.302,0.427 0.219,0.177 10 false *f
*a Protrusion
*b Cutout
*c Top
*d Front of Vehicle
*e Locked
*f Unlocked


Install the air cleaner assembly with air cleaner hose to the throttle body with motor assembly and unlock the hose clip to secure it as shown in the illustration.

NOTICE:

Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly.



b.

Insert the air cleaner assembly with air cleaner hose 3 pins into the air cleaner support.


c.
A432631C01
0.938,1.469 1.042,1.292 1.042,1.292 1.156,1.292 true 0.854,1.073 1.021,1.229 0.167,0.156 10 false *a 0.021,1.542 0.188,1.708 0.167,0.167 10 true *b 0.115,1.354 0.292,1.531 0.177,0.177 10 false *c 0.125,1.729 0.344,1.927 0.219,0.198 10 false *c 1.198,1.208 1.396,1.406 0.198,0.198 10 false *d
*a Top
*b Front of Vehicle
*c 45° (Claw of Clip Location)
*d Paint Mark


Connect the No. 2 PCV hose to the cylinder head cover sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



d.

Connect the vacuum hose to the air cleaner hose.


e.

Attach the 3 wire harness clamps.


f.

Connect the mass air flow meter sub-assembly connector.


Hide 17750A 3.INSTALL INLET AIR CLEANER ASSEMBLY

a.
A434461E01
1.344,1.865 1.49,2.042 0.146,0.177 10 true 1 0.688,1.865 0.833,2.042 0.146,0.177 10 true 2

Install the inlet air cleaner assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12601B 4.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 5.ADD ENGINE COOLANT

Hide 6.INSPECT FOR COOLANT LEAK