Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR
RM3620E _51 Engine / Hybrid System _076382 A25A-FKS ENGINE CONTROL _0373082 AIR FUEL RATIO SENSOR A

A25A-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor.



PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor.



a.

for Sensor 2:

i.
A432693C01
2.865,0.281 2.719,0.281 2.719,0.281 2.635,0.573 true 2.885,0.198 3.208,0.406 0.323,0.208 10 true SST 1.635,0.813 1.823,1 0.188,0.188 10 true *a
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the front exhaust pipe assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.
A450534C01
2.521,0.552 2.604,0.229 2.604,0.229 2.74,0.229 true 2.198,0.719 2.448,0.938 2.448,0.938 2.615,0.729 true 2.771,0.125 2.958,0.323 0.188,0.198 10 true *a 2.385,0.958 2.573,1.135 0.188,0.177 10 true *b
*a White Heat Shrinking Tube
*b Wire Harness Clamp


Connect the air fuel ratio sensor connector.


iii.

Attach the 2 wire harness clamps so that the white heat shrinking tube is positioned as shown in the illustration.



b.

for Sensor 1:

i.
A432688C01
1.031,1.198 0.885,1.5 0.885,1.5 0.75,1.5 true 0.458,1.417 0.75,1.615 0.292,0.198 10 true SST 1.333,0.563 1.521,0.75 0.188,0.188 10 true *a
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.
A432689C01
2.708,0.427 2.865,0.26 2.865,0.26 2.979,0.26 true 2.521,0.427 2.49,0.802 2.49,0.802 2.844,0.813 true 3,0.177 3.167,0.365 0.167,0.188 10 true *a 2.323,0.802 2.5,0.99 0.177,0.188 10 true *b
*a Tie Band
*b Wire Harness Clamp


Connect the air fuel ratio sensor connector.


iii.

Attach the 3 wire harness clamps so that the tie band is positioned as shown in the illustration.



Hide 12601B 2.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY