Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL TANK (w/ Canister Pump Module)
RM3620E _51 Engine / Hybrid System _076683 A25A-FKS FUEL _0373217 FUEL TANK(w/ Canister Pump Module) A

A25A-FKS FUEL  FUEL TANK(w/ Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77606 1.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

Attach the 4 clips and install the No. 1 fuel tank protector sub-assembly to the fuel tank assembly.


Hide 77651A 2.INSTALL NO. 1 FUEL TANK CUSHION

a.

Install 2 new No. 1 fuel tank cushions to the fuel tank assembly.


Hide 77209C 3.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Attach the clamp and install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77100 4.INSTALL FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.

Set the fuel tank assembly on an engine lifter.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.
A434640N01
2.813,1.833 2.969,2.021 0.156,0.188 10 true 1 0.521,1.958 0.677,2.146 0.156,0.188 10 true 2

Using the engine lifter, slowly raise the fuel tank assembly, and temporarily install the fuel tank assembly and 2 fuel tank band sub-assemblies with the 2 bolts in the order shown in the illustration.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




c.
A434630N01
2.844,0.021 3,0.219 0.156,0.198 10 true 1 2.823,1.823 2.979,2.021 0.156,0.198 10 true 2 0.385,0.042 0.531,0.24 0.146,0.198 10 true 3 0.531,1.969 0.667,2.135 0.135,0.167 10 true 4

Using SST, tighten the 4 bolts in the order shown in the illustration.

SST
09961-00950  

Torque:
Specified tightening torque:

45 N*m (459 kgf*cm, 33 ft.*lbf)


HINT:
A434521C01
1.25,1.302 1.25,1.135 1.25,1.135 1.333,0.813 true 2.229,3.854 2.229,3.688 2.229,3.688 2.146,3.438 true 0.083,0.115 0.333,0.292 0.25,0.177 10 true *a 0.115,2.615 0.365,2.802 0.25,0.188 10 true *b 2.458,1.906 2.708,2.083 0.25,0.177 10 true *c 1.167,4.479 1.417,4.656 0.25,0.177 10 true *c 1.167,1.323 1.51,1.5 0.344,0.177 10 true SST 2.104,3.875 2.448,4.052 0.344,0.177 10 true SST
*a LH Side
*b RH Side
*c Torque Wrench Fulcrum Length


·

Using SST, install the rear side of the fuel tank band.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 24.5 N*m (250 kgf*cm, 18 ft.*lbf)




Hide 5.CONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY

a.

Connect the fuel tank filler pipe sub-assembly to the fuel tank filler pipe assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 6.CONNECT FUEL TANK BREATHER TUBE

a.

Connect the fuel tank breather tube to the fuel tank filler pipe assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209C 7.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly to the fuel tube.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 8.CONNECT FUEL TANK VENT TUBE

a.

Attach the clamp and connect the fuel tank vent tube.


b.

Connect the fuel tank vent tube to the fuel tank vent hose sub-assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77606 9.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the fuel tank band with the 2 nuts.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 58398F 10.INSTALL NO. 1 FLOOR UNDER COVER

a.

Install the No. 1 floor under cover to the body and tighten the nut.


b.

Attach the 3 clips and install the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58165C 11.INSTALL FRONT FLOOR COVER RH

a.

Install the front floor cover RH to the body and tighten the 3 nuts.


b.

Attach the 2 clips and install the 2 bolts and 4 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58399D 12.INSTALL NO. 2 FLOOR UNDER COVER

a.

Install the No. 2 floor under cover to the body and tighten the 4 nuts.


b.

Attach the 3 clips and install the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58166A 13.INSTALL FRONT FLOOR COVER LH

a.

Install the front floor cover LH to the body and tighten the 3 nuts.


b.

Attach the 3 clips and install the 2 bolts and 5 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51420 14.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51441 15.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53895B 16.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

Hide 53896B 17.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

Hide 37110 18.INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)

Hide 17408 19.INSTALL TAIL EXHAUST PIPE ASSEMBLY

Hide 20.ADD FUEL

Hide 77020A 21.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION