Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370280 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Parking Brake Switch Circuit  


DESCRIPTION

This circuit is from the skid control ECU (brake actuator assembly) to the radio and display receiver assembly.*1

This circuit is from the parking brake ECU (brake actuator assembly) to the radio and display receiver assembly.*2

*1: for Gasoline Model

*2: for HV Model


WIRING DIAGRAM

E372242E46
2.5,1.479 3.104,1.719 0.604,0.24 10 false A39 2.5,1.646 4.021,2.094 1.521,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 3.688,0.99 4.292,1.229 0.604,0.24 10 false 35 5.219,1.99 5.823,2.229 0.604,0.24 10 false G2 5.219,2.146 6.406,2.594 1.188,0.448 10 false Radio and Display Receiver Assembly 5.417,1.083 6.021,1.323 0.604,0.24 10 false PKB 5.146,0.99 5.75,1.229 0.604,0.24 10 false 20 3.313,1.115 3.917,1.354 0.604,0.24 10 false PKB 0.313,0.208 3.802,0.448 3.49,0.24 12 false for Gasoline Model:

E372242E45
2.5,1.479 3.104,1.719 0.604,0.24 10 false M36 2.5,1.646 4.146,2.115 1.646,0.469 10 false Parking Brake ECU (Brake Actuator Assembly) 3.688,0.99 4.292,1.229 0.604,0.24 10 false 5 5.219,1.99 5.823,2.229 0.604,0.24 10 false G2 5.219,2.146 6.406,2.594 1.188,0.448 10 false Radio and Display Receiver Assembly 5.417,1.083 6.021,1.323 0.604,0.24 10 false PKB 5.146,0.99 5.75,1.229 0.604,0.24 10 false 20 3.313,1.115 3.917,1.354 0.604,0.24 10 false PKB 0.313,0.198 2.698,0.438 2.385,0.24 12 false for HV Model:

PROCEDURE

1.CHECK BRAKE WARNING LIGHT
a.

Check that the brake warning light comes on when the parking brake is applied and goes off when it is released.

OK:

The brake warning light operates as specified above.



Result:
Result Proceed to
OK (for Gasoline Model) A
OK (for HV Model) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU [BRAKE ACTUATOR ASSEMBLY] - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU [BRAKE ACTUATOR ASSEMBLY] - RADIO AND DISPLAY RECEIVER ASSEMBLY)

C

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU [BRAKE ACTUATOR ASSEMBLY] - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-20 (PKB) - A39-35 (PKB) Always Below 1 Ω
G2-20 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU [BRAKE ACTUATOR ASSEMBLY] - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the M36 parking brake ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-20 (PKB) - M36-5 (PKB) Always Below 1 Ω
G2-20 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR