Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3620E _51 Engine / Hybrid System _076384 M20A-FKS ENGINE CONTROL _0372800 SFI SYSTEM C

M20A-FKS ENGINE CONTROL  SFI SYSTEM  P05A211  Active Grille Air Shutter "A" Circuit Short to Ground  P05A212  Active Grille Air Shutter "A" Circuit Short to Battery  P05A213  Active Grille Air Shutter "A" Circuit Open  


DESCRIPTION

Refer to DTC P059F73.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>P059F73

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P05A211 Active Grille Air Shutter "A" Circuit Short to Ground Either of the following conditions is met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·

Short to ground detected in the grille shutter motor (swing grille actuator assembly) when a grille shutter operation is requested.

·

Short to ground detected in the motor drive circuit when a grille shutter operation is requested.


Swing grille actuator assembly - DTC stored SAE: P05A5
P05A212 Active Grille Air Shutter "A" Circuit Short to Battery Either of the following conditions is met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·

Short to +B detected in the grille shutter motor (swing grille actuator assembly) when a grille shutter operation is requested.

·

Short to +B detected in the motor drive circuit when a grille shutter operation is requested.


Swing grille actuator assembly - DTC stored SAE: P05A4
P05A213 Active Grille Air Shutter "A" Circuit Open Either of the following conditions is met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·

Open detected in the grille shutter motor (swing grille actuator assembly) when a grille shutter operation is requested.

·

Open detected in the grille shutter motor circuit when a grille shutter operation is requested.

·

Internal malfunction detected in the grille shutter ECU (swing grille actuator assembly) when a grille shutter operation is requested.


Swing grille actuator assembly - DTC stored SAE: P05A2

HINT:

*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.


MONITOR DESCRIPTION

1.

Grille Shutter Motor (Swing Grille Actuator Assembly) Malfunction

If the grille shutter ECU (swing grille actuator assembly) detects a malfunction in the grille shutter motor drive circuit when a grille shutter operation is requested, it will output a malfunction signal to the ECM and the ECM will store a DTC.

Detection Condition DTC No.
Short to Ground P05A211 (Active Grille Air Shutter "A" Circuit Short to Ground)
Short to +B P05A212 (Active Grille Air Shutter "A" Circuit Short to Battery)
Open P05A213 (Active Grille Air Shutter "A" Circuit Open)

2.

Grille Shutter ECU Internal Malfunction

If the grille shutter ECU detects an internal malfunction, it will output a malfunction signal to the ECM and the ECM will store a DTC.

Detection Condition DTC No.
EEPROM Malfunction P05A213 (Active Grille Air Shutter "A" Circuit Open)
Analog/Digital Conversion Malfunction


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.

9.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

10.

Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

11.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.


12.

Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

13.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



CAUTION / NOTICE / HINT

NOTICE:

In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.

Body Electrical > Grille Shutter > Utility
Tester Display
Grille Shutter Control Mode Switching
50005 352 4221

e.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.


Result:
Proceed to
NEXT



NEXT

2.REPLACE SWING GRILLE ACTUATOR ASSEMBLY
2.REPLACE SWING GRILLE ACTUATOR ASSEMBLY
a.

Replace the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

3.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING AND GRILLE SHUTTER INITIALIZATION)
3.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING AND GRILLE SHUTTER INITIALIZATION)
HINT:

When changing the grille shutter control mode and/or performing initialization by driving the vehicle, the grille shutter control mode can only be changed and initialization can only be performed if the grille shutter system is in maintenance mode.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM (for Gasoline Model)>INITIALIZATION


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.

Body Electrical > Grille Shutter > Utility
Tester Display
Grille Shutter Control Mode Switching
50005 352 4221

e.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.


f.

Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Initialization.

Body Electrical > Grille Shutter > Utility
Tester Display
Grille Shutter Initialization
50005 352 4467

g.

According to the display on the GTS, perform Grille Shutter Initialization.


h.

Enter the following menus: Body Electrical / Grille Shutter / Data List / Shutter Control State and Shutter Initialization.

Body Electrical > Grille Shutter > Data List
Tester Display
Shutter Control State
Shutter Initialization
50003 352 10,29

i.

According to the display on the GTS, read the Data List and check that the value of Shutter Control State is "Normal" and Shutter Initialization is "Complete".


Result:
Proceed to
NEXT



NEXT

END