Refer to DTC P059F73.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>P059F73
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P05B112 | Active Grille Air Shutter "B" Circuit Short to Battery | All of the following conditions are met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·
The battery voltage is 10.5 to 16 V. ·
Grille shutter opening or closing operation is being performed. ·
The Hall IC1 signal or Hall IC2 signal is stuck on the high side when the other signal is received normally. |
Swing grille actuator assembly | - | DTC stored | SAE: P05B3 |
| P05B114 | Active Grille Air Shutter "B" Circuit Short to Ground or Open | All of the following conditions are met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·
The battery voltage is 10.5 to 16 V. ·
Grille shutter opening or closing operation is being performed. ·
The Hall IC1 signal or Hall IC2 signal is stuck on the low side when the other signal is received normally. |
Swing grille actuator assembly | - | DTC stored | SAE: P05B4 |
| P05B131 | Active Grille Air Shutter "B" No Signal | Both of the following conditions are met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
·
Grille shutter opening or closing operation is being performed. ·
The Hall IC1 signal and Hall IC2 signal are not received while the grille shutter motor (swing grille actuator assembly) is operating. |
Swing grille actuator assembly | - | DTC stored | SAE: P05B2 |
*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.
Hall IC Signal Malfunction
If the grille shutter ECU (swing grille actuator assembly) detects a stuck high or stuck low signal from either hall IC1 or hall IC2, it will output a malfunction signal to the ECM and the ECM will store a DTC.
| Detection Condition | DTC No. |
|---|---|
| Short to +B (Stuck High) | P05B112 (Active Grille Air Shutter "B" Circuit Short to Battery) |
| Open or Short to Ground (Stuck Low) | P05B114 (Active Grille Air Shutter "B" Circuit Short to Ground or Open) |
Hall IC Signal Reception Malfunction
If the grille shutter ECU (swing grille actuator assembly) detects a stuck high or stuck low signal from both hall IC1 and hall IC2, it will output a malfunction signal to the ECM and the ECM will store a DTC.
| Detection Condition | DTC No. |
|---|---|
| Abnormal Signal (Hall IC1 and Hall IC2) | P05B131 (Active Grille Air Shutter "B" No Signal) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.
According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.
Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
"Normal" is displayed.
Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
"Normal" is displayed.
In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.
| Tester Display |
|---|
| Grille Shutter Control Mode Switching |
According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the swing grille actuator assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
When changing the grille shutter control mode and/or performing initialization by driving the vehicle, the grille shutter control mode can only be changed and initialization can only be performed if the grille shutter system is in maintenance mode.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM (for Gasoline Model)>INITIALIZATION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.
| Tester Display |
|---|
| Grille Shutter Control Mode Switching |
According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.
Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Initialization.
| Tester Display |
|---|
| Grille Shutter Initialization |
According to the display on the GTS, perform Grille Shutter Initialization.
Enter the following menus: Body Electrical / Grille Shutter / Data List / Shutter Control State and Shutter Initialization.
| Tester Display |
|---|
| Shutter Control State |
| Shutter Initialization |
According to the display on the GTS, read the Data List and check that the value of Shutter Control State is "Normal" and Shutter Initialization is "Complete".
| Proceed to |
|---|
| NEXT |
NEXT