Home › Vehicle Interior › HEATING / AIR CONDITIONING › REFRIGERANT (for HFO-1234yf(R1234yf))
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374852 REFRIGERANT(for HFO-1234yf(R1234yf)) A

HEATING / AIR CONDITIONING  REFRIGERANT(for HFO-1234yf(R1234yf))  REPLACEMENT  


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

a.

for HV Model:

i.

Turn the power switch on (READY).



b.

for Gasoline Model:

i.

Start the engine.



c.

Operate the compressor under the following conditions:

Item Condition
Operating time 3 minutes or more
Temperature setting Max cold
Blower speed High
Power switch (for HV Model) On (READY)
Engine (for Gasoline Model) Idling
A/C switch On

This causes most of the compressor oil from the various components of the A/C system to collect in the compressor.

HINT:

It is not necessary to operate the compressor if the A/C does not operate because of compressor lock, etc.



d.

for HV Model:

i.

Turn the power switch off.



e.

for Gasoline Model:

i.

Stop the engine.



f.

Recover the refrigerant from the A/C system using a refrigerant recovery unit.

HINT:

Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



Hide 2.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

HINT:

Charge the system with refrigerant in accordance with the manufacturer's instruction manual.


a.

Perform vacuum purging using a vacuum pump or appropriate equipment.

NOTICE:

Be sure to use a refrigerant recovery unit that is compatible with HFO-1234yf (R1234yf) systems.



b.

Charge the air conditioning system with refrigerant.

Refrigerant Type:

HFO-1234yf (R1234yf)


E247093C07
4.531,1.74 4.792,0.99 4.792,0.99 4.885,0.99 false 2.604,0.344 2.813,0.563 0.208,0.219 10 false *a 4.917,0.906 5.125,1.125 0.208,0.219 10 false *b 5.75,1.531 5.958,1.75 0.208,0.219 10 false *c 1.667,3.302 1.938,3.5 0.271,0.198 10 false : *e 3.781,3.104 3.99,3.323 0.208,0.219 10 false *f 0.875,1.552 1.083,1.771 0.208,0.219 10 false *d 4.406,2.198 4.625,2.417 0.219,0.219 10 false *g
*a Standard Charge Amount *b Mean Value in Proper Range
*c Overcharged *d High Pressure
*e Sub-cool System *f Refrigerant Amount
*g +/-30 g (+/-1.05 oz) - -


Standard Charge Amount:

520 to 580 g (18.4 to 20.4 oz)


NOTICE:
·

Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to operate without refrigerant, resulting in overheating of the compressor.

·

The refrigerant amount should be checked by quantity (weight).

·

The graph above is shown for reference only.



HINT:

Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



Hide 3.WARM UP COMPRESSOR (for HV Model)

a.

Keep the A/C switch on for at least 2 minutes to warm up the compressor.

NOTICE:

To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing any air conditioning system lines (including the compressor).



Hide 4.WARM UP ENGINE (for Gasoline Model)

a.

Warm up the compressor under the following conditions.

NOTICE:

To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing any air conditioning system lines (including the compressor).


Item Condition
Operating time 1 minute or more
Temperature setting Max cold
Blower speed High
Engine speed 2000 rpm or less
A/C switch On


Hide 5.INSPECT FOR REFRIGERANT LEAK

a.

After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a gas leak detector.

HINT:

Be sure to use a gas leak detector that is compatible with HFO-1234yf (R1234yf) systems.



b.

Carry out the test under the following conditions:

·

Turn the ignition switch off.

·

Ensure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).

·

Repeat the inspection 2 or 3 times.

·

Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.

Pressure when the compressor is off: approximately 392 to 588 kPa (3.9 to 5.9 kgf/cm2, 57 to 85 psi)



c.
E268308C01
2.688,1.896 2.688,1.646 false 0.167,0.167 0.479,0.365 0.313,0.198 10 *a 2.635,1.906 2.948,2.104 0.313,0.198 10 *b
*a Inspect for Leak
*b Gas Leak Detector


Using a gas leak detector, inspect for refrigerant leaks from the air conditioning system.


d.
E280081C01
0.844,1.083 1.26,1.083 false 1.083,1.469 1.083,1.802 false 0.677,0.979 0.99,1.177 0.313,0.198 10 false *1 1.021,1.813 1.333,2.01 0.313,0.198 10 false *a
*1 Drain Cooler Hose
*a Gas Leak Detector


Bring the gas leak detector close to the drain cooler hose with the detector power off, and then turn the detector on.

HINT:
·

After the blower motor has stopped, leave the cooling unit for more than 15 minutes.

·

Bring the gas leak detector sensor under the drain cooler hose.

·

When bringing the gas leak detector close to the drain cooler hose, make sure that the gas leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.




e.

If a refrigerant leak is not detected from the drain cooler hose, remove the blower motor from the cooling unit. Insert the gas leak detector sensor into the unit and check for leaks.


f.

Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure sensor and check for leaks.

HINT:

When checking for leaks, the presence of oily dirt at a joint can indicate a leak.