Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370835 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the back-up light switch assembly.

WIRING DIAGRAM

E404537E05
0.083,1 1.594,1.375 1.51,0.375 10 false from IG1 NO.1 Relay 2.031,1.229 2.823,1.531 0.792,0.302 10 false BKUP LP 3.229,0.875 3.417,1.063 0.188,0.188 10 false 2 4.49,0.885 4.677,1.073 0.188,0.188 10 false 1 3,1.292 3.354,1.479 0.354,0.188 10 false C11 2.99,1.458 5,1.708 2.01,0.25 10 false Back-up Light Switch Assembly 5.135,0.854 5.344,1.063 0.208,0.208 10 false 28 5.427,0.969 5.833,1.177 0.406,0.208 10 false REV 5.167,1.583 5.573,1.792 0.406,0.208 10 false G3 5.167,1.76 6.875,2.104 1.708,0.344 10 false Radio and Display Receiver Assembly 3.448,0.906 3.854,1.115 0.406,0.208 10 false RB 4.177,0.885 4.583,1.094 0.406,0.208 10 false RL

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK VEHICLE SIGNAL (DISPLAY CHECK MODE)
a.
E270655

Enter the "Function Check/Setting I" mode and select "Vehicle Signal".

w/ Navigation System;

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK

w/ Audio and Visual System (for Radio and Display Type):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>OPERATION CHECK


b.

Check that the "REV" item on the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY
2.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)

NG

3.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
a.
E404555C01
1.469,0.521 1.896,0.781 0.427,0.26 2.01,2.615 2.219,2.615 2.219,2.615 2.594,2.083 true 0.146,0.094 0.5,0.313 0.354,0.219 10 false *a 1.677,2.542 2.063,2.74 0.385,0.198 10 false REV 1.552,0.563 1.938,0.76 0.385,0.198 10 false G3
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G3-28 (REV) - Body ground Ignition switch ON
Shift position in R
11 to 14 V
G3-28 (REV) - Body ground Ignition switch ON
Shift position not in R
Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR