Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0369994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B278D  Malfunction of ID-BOX Recognition  


DESCRIPTION

When the certification ECU (smart key ECU assembly) detects an input signal indicating that the vehicle is equipped with an ID code box even though the ID code box is not registered, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B278D Malfunction of ID-BOX Recognition One of the following conditions is met:
·

The certification ECU (smart key ECU assembly) recognizes that the wire harness judging whether the vehicle is equipped with an ID code box or not is provided even though the ID code box is not registered.

·

The certification ECU (smart key ECU assembly) receives a LIN signal from the ID code box even though the ID code box is not registered.

·

The certification ECU (smart key ECU assembly) receives a LIN signal from the ID code box even though the wire harness judging whether the vehicle is equipped with an ID code box or not is not provided.


Misconnection of the ID code box DTC output confirmation operation:

Always



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Key registration will be prohibited -

Related Data List and Active Test
DTC No. Data List and Active Test
B278D -

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before performing following procedure, check that the ID code box (immobiliser code ECU) is not installed on the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.


b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Result Proceed to
DTC B278D is not output. A
DTC B278D is output. B



A

END

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)