Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Triple Beam Headlight)
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375585 HEADLIGHT ASSEMBLY(for Triple Beam Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Triple Beam Headlight)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 81160A 1.INSTALL HEADLIGHT LED UNIT ASSEMBLY LH

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the headlight LED unit assembly LH with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wipe with a soft cloth.

·

If there are fingerprints on the inner surface of the lens, lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04020, 09891-04010, 09891-04030, 09891-04040)

a.
E404036C01
0.5,3.219 0.698,3.396 0.198,0.177 10 true *a
*a Rail


Set the headlight LED unit assembly LH onto the rail and aiming screws for beam axis vertical and horizontal adjustments.

HINT:

Set it into place by aligning the arrows shown in the illustration: black with black, and white with white.



b.
E404034C01
0,0 0,0 false
V113147

Tighten in this Direction


Hold the headlight LED unit assembly LH with one hand to prevent it from tipping over and make the aiming screws for beam axis vertical and horizontal adjustments flush with the aiming screw holder by tightening it clockwise.

NOTICE:

Do not touch the metallic surface to the headlight LED unit assembly LH.



c.

Push the part shown in the illustration to connect the pivot.

E404037C01
4.49,0.573 4.667,0.771 0.177,0.198 10 true *a
*a Pivot - -
V100135

Push Here - -



d.
E404034C01
0,0 0,0 false
V113147

Tighten in this Direction


Tighten the aiming screws for beam axis vertical and horizontal adjustments until the protrusion amount is the same as that recorded.


e.
E404031

Connect the connector.


f.
E404030

Attach the guide to set the turn signal reflector with inner lens.


g.

Install the 3 screws.


Hide 81132B 2.INSTALL HEADLIGHT LENS GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are fingerprints on the inner surface of the lens, lightly wipe with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E404019C01
0,0 0,0 false
V100155

Area to Clean


Clean the headlight lens gasket installation groove.


b.

Prepare 2 screwdrivers, fold a piece of peeling paper over the tip of each screwdriver and fix the pieces of peeling paper in place with tape.

HINT:

Use the peeling paper that is supplied with the headlight lens gasket.



c.
E318045

Using scissors, cut the headlight lens gasket at a 90° angle.


d.
E404021C01
0,0 0,0 false
V100143

Starting Point
V113147

Install in this Direction


Starting from the position shown in the illustration, set the headlight lens gasket into the straight groove clockwise until it meets the corner groove.

NOTICE:

Lightly set the gasket in place without pulling.



e.

Fold the peeling paper over the tip of a screwdriver and fix it in place with tape.

NOTICE:

Use the peeling paper that is supplied with the seal.



f.
E404023C01
0,0 0,0 false
V100136

Corner Groove
V100146

Headlight Lens Gasket
V100155

Peeling Paper


Set the headlight lens gasket into the corner groove and using 2 screwdrivers with their tips wrapped with peeling paper, push the gasket into the bottom of the groove.

NOTICE:
·

Lightly set the gasket in place without pulling.

·

If the headlight lens gasket is set while pulled, the gasket will be pushed up at the corner groove.




g.

Repeat the following order while working in a circle back to the starting point.

i.

Set headlight lens gasket into straight groove.


ii.

Push into bottom of groove.


iii.

Set into corner groove.


iv.

Push into bottom of groove.



h.
E404025C01
1.656,2.469 1.969,2.625 0.313,0.156 10 false *a
*a 20 mm (0.7874 in.)
V100136

Corner Groove


Using scissors, cut the headlight lens gasket at a 45° angle at the starting point so that the gasket overlaps itself 20 mm (0.7874 in.) and set the gasket in place.


i.

Check the installation condition of the headlight lens gasket.

OK:

Gasket not pushed up or protruding.

No gap where gasket overlaps.


NOTICE:

Check the corners carefully since the gasket can easily become pushed up in those areas.



Hide 8110B 3.INSTALL HEADLIGHT LENS SUB-ASSEMBLY LH

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E404027C01
0,0 0,0 false
V100155

Area to Clean


Clean the headlight lens gasket contact surface.


b.

Set the headlight lens LH sub-assembly LH straight down in place.

NOTICE:
E317610C01
0,0 0,0 false
V100144

Headlight Lens Gasket
V100146

Headlight Housing
V100155

Headlight Lens Sub-assembly LH


Set the headlight lens LH sub-assembly LH in the middle of the headlight lens gasket as shown in the illustration.


E404017C01
0,0 0,0 false
V113147

Set in this Direction - -



c.

Check that the entire circumference of the headlight lens LH sub-assembly LH is positioned above the middle of the headlight lens gasket.


d.

Install the headlight lens LH sub-assembly LH:

HINT:

Install the headlight lens LH sub-assembly LH to the headlight housing from the starting point of installation toward the inside of the vehicle as shown in the illustration.

E404029C01
4.823,0.469 5.24,0.865 0.417,0.396 4.833,0.479 5,0.667 0.167,0.188 10 true *a
*a Installation Starting Point - -
V113147

Install in this Direction - -



i.

Attach the claw to install the headlight lens LH sub-assembly LH.

E404009


ii.
E404008C01
3.031,2.229 3.25,2.417 0.219,0.188 10 false *a
*a "TORX" Screw


Install the 7 screws.


iii.

Using a T20H "TORX" driver, install the "TORX" screw.


iv.

Check the condition of the headlight lens gasket.

OK:

Gasket contacts headlight lens LH sub-assembly LH and does not protrude out.




e.
E404007

Connect the connector.


f.
E404006C01
0.385,0.656 1.063,0.927 true 1.031,1.906 1.219,1.021 true 1.51,2.938 2.427,2.594 true 0.948,1.938 1.146,2.135 0.198,0.198 10 true *a 0.188,0.563 0.365,0.74 0.177,0.177 10 true *b 2.479,2.479 2.688,2.656 0.208,0.177 10 true *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark
V113147

Turn in this Direction


Align the matchmark of the headlight back cover with the unlock position mark, and then turn the headlight back cover clockwise until the lock position mark to install the headlight back cover.


Hide 81134 4.INSTALL HEADLIGHT GASKET

Hide 81056A 5.INSTALL HEADLIGHT ECU SUB-ASSEMBLY LH

Hide 81194A 6.INSTALL HEADLIGHT PROTECTOR LH

a.
E403990C01
0,0 0,0 false
V100155

Area to Clean


Clean the application area of the headlight protector LH shown in the illustration.

NOTICE:

Remove any remaining double-sided tape, and then clean and degrease the area.



b.
E403989

Remove approximately 3.0 cm (1.18 in.) of the peeling paper from a new headlight protector LH.


c.
E403992C01
1.385,2.344 1.833,2.646 0.448,0.302 1.396,2.354 1.583,2.521 0.188,0.167 10 true *a
*a Application Start Position
V113147

Set in this Direction


Align the angle of the headlight protector LH with the application start position, and then set only the part with peeling paper removed into place.


d.

Press the set portion of the part with your finger to secure it.

NOTICE:

Do not slide your finger horizontally, as doing so may stretch the part unnecessarily.



e.
E403991C01
0,0 0,0 false
V113147

Install in this Direction


Align with the curve and set only the part where the peeling type tape was removed from into place.


f.
E403993C01
0,0 0,0 false
V100135

Press Here


Press the set portion of the part with your finger to secure it.

NOTICE:

Do not slide your finger horizontally, as doing so may stretch the part unnecessarily.



Hide 81510C 7.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.
E403987C01
0,0 0,0 false
V113147

Install in this Direction


Install the front turn signal light bulb to the bulb socket.


b.
E409870C01
0.917,1.698 1.26,0.333 true 2.594,1.552 1.385,0.531 true 1.74,2.823 2.625,2.5 true 2.646,1.521 2.958,1.677 0.313,0.156 10 false *a 0.833,1.75 1.146,1.906 0.313,0.156 10 false *b 2.677,2.406 2.99,2.563 0.313,0.156 10 false *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark
V113147

Turn in this Direction


Align the matchmark of the bulb socket with the unlock position mark, and then turn the bulb socket clockwise until the lock position mark to connect the bulb socket.


c.
E407142

Connect the connector.


Hide 81134D 8.INSTALL NO. 2 HEADLIGHT GASKET

a.
B552302

Install a new No. 2 headlight gasket.


Hide 81156A 9.INSTALL HEADLIGHT BRACKET LH

a.
B552301C01
2.688,1.219 2.958,0.823 true 2.479,1.156 2.698,0.75 true 2.792,4.156 2.333,4.365 true 2.635,0.573 2.833,0.729 0.198,0.156 10 true *a 2.958,0.625 3.135,0.781 0.177,0.156 10 true *b 2.823,4.042 3.031,4.219 0.208,0.177 10 true *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark
V113147

Turn in this Direction


Align the matchmark of the headlight bracket LH with the unlock position mark, and then turn the bulb socket clockwise until the lock position mark to connect the headlight bracket LH.


b.
B552299C02
0,0 0,0 false
V100135

Connector
V100136

"TORX" Screw


Using a T20H "TORX" driver, install the "TORX" screw.


c.

Connect the connector.