Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0375764 FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory)  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (Rearward) ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front Reclining switch signal (Forward) ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-
Front Vertical Down Front vertical switch signal (Downward) ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up Front vertical switch signal (Upward) ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down Rear lifter switch signal (Downward) ON or OFF ON: Rear lifter switch (Downward) on
OFF: Rear lifter switch (Downward) off
-
Lifter Switch Up Rear lifter switch signal (Upward) ON or OFF ON: Rear lifter switch (Upward) on
OFF: Rear lifter switch (Upward) off
-
Slide Rear Slide switch signal (Rearward) ON or OFF ON: Slide switch (Rearward) on
OFF: Slide switch (Rearward) off
-
Slide Front Slide switch signal (Forward) ON or OFF ON: Slide switch (Forward) on
OFF: Slide switch (Forward) off
-
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No3 Seat position memorized with M3 switch* Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
Not applicable
Ignition Switch Communication state of engine switch signal ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off or on (ACC)
-
Parking Brake SW Parking brake switch status ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Vehicle Speed Vehicle speed data Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
Slide Position Seat sliding position Min: 0, Max: 65535 Within range from 0 to 65535 -
Reclining Position Seat reclining position Min: 0, Max: 65535 Within range from 0 to 65535 -
Front Vertical Position Seat front vertical position Min: 0, Max: 65535 Within range from 0 to 65535 -
Lifter Position Seat lifter position Min: 0, Max: 65535 Within range from 0 to 65535 -
Slide Pos Mem No1 Seat slide position memorized with M1 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
Reclining Pos Mem No1 Seat reclining position memorized with M1 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
Frnt Vrtcl Pos Mem No1 Front vertical position memorized with M1 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
Lifter Pos Mem No1 Lifter position memorized with M1 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
Slide Pos Mem No2 Seat slide position memorized with M2 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
Reclining Pos Mem No2 Seat reclining position memorized with M2 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
Frnt Vrtcl Pos Mem No2 Front vertical position memorized with M2 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
Lifter Pos Mem No2 Lifter position memorized with M2 switch Min: 0, Max: 65535 Within range from 0 to 65535 -
Slide Pos Mem No3 Seat slide position memorized with M3 switch* Min: 0, Max: 65535 Within range from 0 to 65535 Not applicable
Reclining Pos Mem No3 Seat reclining position memorized with M3 switch* Min: 0, Max: 65535 Within range from 0 to 65535 Not applicable
Frnt Vrtcl Pos Mem No3 Front vertical position memorized with M3 switch* Min: 0, Max: 65535 Within range from 0 to 65535 Not applicable
Lifter Pos Mem No3 Lifter position memorized with M3 switch* Min: 0, Max: 65535 Within range from 0 to 65535 Not applicable
Lumbar Switch Front Lumbar support adjuster switch signal (Forward) ON or OFF ON: Lumbar support adjuster switch (Forward) on
OFF: Lumbar support adjuster switch (Forward) off
-
Lumbar Switch Rear Lumbar support adjuster switch signal (Rearward) ON or OFF ON: Lumbar support adjuster switch (Rearward) on
OFF: Lumbar support adjuster switch (Rearward) off
-
Lifter Initialize Flag Seat lifter limit position memory ON or OFF ON: Memorized
OFF: Not memorized
-
Front Vertical Init Flag Seat front vertical limit position memory ON or OFF ON: Memorized
OFF: Not memorized
-
Reclining Position Init Flg Seat reclining limit position memory ON or OFF ON: Memorized
OFF: Not memorized
-
Slide Position Init Flag Seat slide limit position memory ON or OFF ON: Memorized
OFF: Not memorized
-
Slide Position Front Limit Seat slide limit position (front) Min: 0, Max: 65535 Within range from 0 to 65535 -
Slide Position Rear Limit Seat slide limit position (rear) Min: 0, Max: 65535 Within range from 0 to 65535 -
Reclining Position Front Limit Seat reclining limit position (front) Min: 0, Max: 65535 Within range from 0 to 65535 -
Reclining Position Rear Limit Seat reclining limit position (rear) Min: 0, Max: 65535 Within range from 0 to 65535 -
Front Vertical UP Limit Seat front vertical limit position (up) Min: 0, Max: 65535 Within range from 0 to 65535 -
Front Vertical Down Limit Seat front vertical limit position (down) Min: 0, Max: 65535 Within range from 0 to 65535 -
Lifter Position UP Limit Seat lifter limit position (up) Min: 0, Max: 65535 Within range from 0 to 65535 -
Lifter Position Down Limit Seat lifter limit position (down) Min: 0, Max: 65535 Within range from 0 to 65535 -
Memory Button Buzzer Request Driver seat buzzer request display OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT OFF: Buzzer does not sound
MOVE: Request to sound buzzer when starting memory replay
REGISTRY: Request to sound buzzer when starting memory registration
CANCEL: Request to sound buzzer when canceling memory call registration
REG NG: Request to sound buzzer when memory call registration not possible
REG WAIT: Request to sound buzzer when starting memory call cabin scan
-
Driver Seat Request Command Driver seat operation request received OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET OFF: No instruction
MEMORY: Request to memorize
MEM MOV: Request to recall memory
MEM SOD: Request to replay
RET MOV: Request to return
AWY MOV: Request to move away
AWY SOD: Request to recall away position memory
MEM AWY: Request to recall memorized position of seatback
MEM RET: Request to restore seatback to memorized position
-
Driver Seat POS REQ Seat memory switch (driver door) operation value OFF, MEM1, MEM2, MEM3*, DRV1*, DRV2* or DRV3* OFF: No operation
MEM1: M1 switch operation status
MEM2: M2 switch operation status
MEM3: M3 switch operation status*
DRV1: Other 1 operation status*
DRV2: Other 2 operation status*
DRV3: Other 3 operation status*
-
Away Move Range Scale Seat travel distance for power easy access system* NONE, SMALL, STANDRD or LONG NONE: Seat travel distance none
SMALL: Seat travel distance short
STANDRD: Seat travel distance normal
LONG: Seat travel distance long
Not applicable
Return Move Return function* NOT AVL or AVAIL NOT AVL: Not available
AVAIL: Available
Not applicable
Return & Away Function Return & away function* NOT AVL or AVAIL NOT AVL: Not available
AVAIL: Available
Not applicable
Driver Seat Buckle SW Driver seat belt buckle switch* ON or OFF ON: Driver seat belt fastened
OFF: Driver seat belt unfastened
Not applicable
Return Position Return position* Min: 0, Max: 65535 Within range from 0 to 65535 Not applicable
Shift SW Position Park state signal Shift P or Shift Other Shift P: Shift lever in P
Shift Other: Shift lever in a position other than P
except Manual Transaxle
ECU Voltage Value Voltage of position control ECU assembly (driver seat) 0 to 655350 mV 11000 to 14000 mV -
Battery Voltage Value Battery voltage 0 to 655350 mV 11000 to 14000 mV -
Auto Operation Interference Avoidance Function Setting status for availability of auto adjustment function that avoids interference between headrest and roof headlining during driver seat operation ON or OFF Customized value displayed -
Number of Trouble Codes Number of trouble codes Min.: 0 or Max.: 255 Number of DTCs will be displayed -

*: Although this item is displayed on the GTS, it is not applicable to this vehicle.



f.

Enter the following menus: Body Electrical / Main Body / Data List.


g.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*2 ON or OFF ON: Driver door open
OFF: Driver door closed
-
FL Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*1 ON or OFF ON: Driver door open
OFF: Driver door closed
-
M1 Switch M1 switch signal ON or OFF ON: M1 switch on
OFF: M1 switch off
-
M2 Switch M2 switch signal ON or OFF ON: M2 switch on
OFF: M2 switch off
-
SET Switch SET switch signal ON or OFF ON: SET switch on
OFF: SET switch off
-
Seat position/Tilt & Telesco memory recall setting Setting of customize function "Seat position/Tilt & Telesco memory recall setting" D Door or Any Door Customize setting displayed -
Mem SW No. w/KeyID1 Memory switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3*3 NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1*3
-
Mem SW No. w/KeyID2 Memory switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3*3 NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2*3
-
Mem SW No. w/KeyID3 Memory switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3*3 NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3*3
-
Mem SW No. w/KeyID4 Memory switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3*3 NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4*3
-
Mem SW No. w/KeyID5 Memory switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3*3 NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5*3
-
Mem SW No. w/KeyID6 Memory switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3*3 NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID6*3
-
Mem SW No. w/KeyID7 Memory switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3*3 NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7*3
-
Driver Seat Memory1 Seat position memorized with M1 switch ON or OFF ON: Memorized
OFF: Not memorized
-
Driver Seat Memory2 Seat position memorized with M2 switch ON or OFF ON: Memorized
OFF: Not memorized
-
D Seat Configuration Position control ECU assembly (driver seat) status NONE, Not RTN or Return NONE: Position control ECU assembly (driver seat) not connected
Not RTN: Position control ECU assembly (driver seat) connected (Not including power seat power easy access system function)
Return: Position control ECU assembly (driver seat) connected (Including power seat power easy access system function)
-

*1: for LHD

*2: for RHD

*3: Although this item is displayed on the GTS, it is not applicable to this vehicle.



h.

Enter the following menus: Body Electrical / Master Switch / Data List.


i.

Read the Data List according to the display on the GTS.

Body Electrical > Master Switch > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock Switch Status Door control switch (multiplex network master switch) lock signal ON or OFF ON: Lock side of door control switch (multiplex network master switch) pushed
OFF: Lock side of door control switch (multiplex network master switch) not pushed
-
Door Unlock Switch Status Door control switch (multiplex network master switch) unlock signal ON or OFF ON: Unlock side of door control switch (multiplex network master switch) pushed
OFF: Unlock side of door control switch (multiplex network master switch) not pushed
-

j.

Enter the following menus: Powertrain / Transmission / Data List.


k.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch status ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
except Manual Transaxle


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Lifter Operation Seat lifter operation OFF/Down/Up -
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Buzzer Buzzer operation OFF/ON -
Lumbar Slide Lumbar support operation OFF/Rear/Front -