Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › MULTI-TERRAIN SELECT SWITCH
RM3620E _52 Drivetrain _076960 GF1A TRANSFER / 4WD / AWD _0375765 MULTI-TERRAIN SELECT SWITCH G

GF1A TRANSFER / 4WD / AWD  MULTI-TERRAIN SELECT SWITCH  INSPECTION  


PROCEDURE

Hide 84010D 1.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY (MULTI-TERRAIN SELECT SWITCH)

a.

for Automatic Transaxle, CVT:

i.
C405113C01
2.646,1.875 2.479,1.875 2.479,1.875 2.479,1.292 true 1.333,0.25 1.5,0.25 1.5,0.25 1.5,1.01 true 1.615,1.875 1.781,1.875 1.781,1.875 1.781,1.292 true 2.094,1.875 1.927,1.875 1.927,1.875 1.927,1.292 true 2.729,1.792 3.083,2.021 0.354,0.229 10 false GND 1.156,0.167 1.354,0.333 0.198,0.167 10 false B 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 1.438,1.792 1.615,1.99 0.177,0.198 10 false B 2.167,1.781 2.417,2.031 0.25,0.25 10 false E
*a Component without harness connected
Integration Control And Panel Assembly (Multi-Terrain Select Switch)


Inspect the multi-terrain select switch:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (B) - 13 (GND) NORMAL mode switch being pushed and held Below 1 Ω
NORMAL mode switch not pushed 10 kΩ or higher
18 (B) - 17 (E) ROCK & DIRT mode switch being pushed and held 0.5 to 0.52 kΩ
ROCK & DIRT mode switch not pushed 10 kΩ or higher
18 (B) - 17 (E) MUD & SAND mode switch being pushed and held 1.97 to 2.05 kΩ
MUD & SAND mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the integration control and panel assembly (multi-terrain select switch).


ii.
C405113C03
0.771,0.271 0.938,0.271 0.938,0.271 0.938,1.021 true 2.646,0.271 2.479,0.271 2.479,0.271 2.479,1.021 true 2.74,0.177 3.073,0.427 0.333,0.25 10 false ILL- 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.469,0.198 0.823,0.5 0.354,0.302 10 false ILL+
*a Component without harness connected
Integration Control And Panel Assembly (Multi-Terrain Select Switch)


Inspect the illumination:

Apply battery voltage to the integration control and panel assembly (multi-terrain select switch) and check that the switch illuminates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 12 (ILL+)
Battery negative (-) → Terminal 1 (ILL-)
Illuminates


If the result is not as specified, replace the integration control and panel assembly (multi-terrain select switch).



b.

for Manual Transaxle:

i.
C405125C01
1.552,1.021 1.552,0.354 1.552,0.354 1.385,0.354 true 1.885,1.021 1.885,0.354 1.885,0.354 2.052,0.354 true 2.052,1.344 2.052,1.927 2.052,1.927 2.219,1.927 true 1.552,1.344 1.552,1.927 1.552,1.927 1.385,1.927 true 1.229,0.271 1.469,0.521 0.24,0.25 10 false B 1.24,1.844 1.479,2.094 0.24,0.25 10 false B 2.302,1.833 2.708,2.083 0.406,0.25 10 false GND 2.115,0.25 2.521,0.5 0.406,0.25 10 false E 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a
*a Component without harness connected
Integration Control And Panel Assembly (Multi-Terrain Select Switch)


Inspect the multi-terrain select switch:

Measure the resistance according to the value(s) in the table below.

Tester Connection Switch Condition Specified Condition
9 (B) - 6 (GND) NORMAL mode switch being pushed and held Below 1 Ω
NORMAL mode switch not pushed 10 kΩ or higher
4 (B) - 2 (E) ROCK & DIRT mode switch being pushed and held 0.5 to 0.52 kΩ
ROCK & DIRT mode switch not pushed 10 kΩ or higher
4 (B) - 2 (E) MUD & SAND mode switch being pushed and held 1.97 to 2.05 kΩ
MUD & SAND mode switch not pushed 10 kΩ or higher

If the result is not as specified, replace the integration control and panel assembly (multi-terrain select switch).


ii.
C405125C02
1.375,1.021 1.375,0.354 1.375,0.354 1.208,0.354 true 2.052,1.031 2.052,0.365 2.052,0.365 2.219,0.365 true 0.719,0.271 1.292,0.479 0.573,0.208 10 false MSW+ 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a 2.323,0.281 2.958,0.5 0.635,0.219 10 false MSW-
*a Component without harness connected
Integration Control And Panel Assembly (Multi-Terrain Select Switch)


Inspect the illumination:

Apply battery voltage to the integration control and panel assembly (multi-terrain select switch) and check that the switch illuminates.

Condition Specified Condition
Battery positive (+) → Terminal 5 (ILL+)
Battery negative (-) → Terminal 1 (ILL-)
Illuminates

If the result is not as specified, replace the integration control and panel assembly (multi-terrain select switch).