84010D
1.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY (ELECTRIC PARKING BRAKE SWITCH) (except Manual Transaxle)
w/o Vacuum Brake Booster:
| *a | Component without harness connected
Integration Control and Panel Assembly (Electric Parking Brake Switch) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 10 (LCK1) - 15 (E) | OFF (Release) | 95.046 to 109.354 kΩ |
| ON (Lock) | 1.98 to 2.42 kΩ | |
| Switch not operated | 95.046 to 109.354 kΩ | |
| 21 (LCK2) -15 (E) | OFF (Release) | 5.394 to 6.206 kΩ |
| ON (Lock) | 0.968 to 1.232 kΩ | |
| Switch not operated | 5.394 to 6.206 kΩ | |
| 22 (RLS1) -15 (E) | OFF (Release) | 0.968 to 1.232 kΩ |
| ON (Lock) | 5.394 to 6.206 kΩ | |
| Switch not operated | 5.394 to 6.206 kΩ | |
| 23 (RLS2) -15 (E) | OFF (Release) | 0.968 to 1.232 kΩ |
| ON (Lock) | 5.394 to 6.206 kΩ | |
| Switch not operated | 5.394 to 6.206 kΩ |
If the result is not as specified, replace the integration control and panel assembly (electric parking brake switch).
w/ Vacuum Brake Booster:
| *a | Component without harness connected
Integration Control and Panel Assembly (Electric Parking Brake Switch) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 20 (SWI1) - 21 (SWI2) | OFF (Release) | Below 1 Ω |
| ON (Lock) | Below 1 Ω | |
| Switch not operated | 10 kΩ or higher | |
| 20 (SWI1) - 22 (SWO1) | OFF (Release) | 10 kΩ or higher |
| ON (Lock) | Below 1 Ω | |
| Switch not operated | 10 kΩ or higher | |
| 20 (SWI1) - 23 (SWO2) | OFF (Release) | Below 1 Ω |
| ON (Lock) | 10 kΩ or higher | |
| Switch not operated | Below 1 Ω | |
| 22 (SWO1) - 21 (SWI2) | OFF (Release) | 10 kΩ or higher |
| ON (Lock) | Below 1 Ω | |
| Switch not operated | Below 1 Ω | |
| 22 (SWO1) - 23 (SWO2) | OFF (Release) | 10 kΩ or higher |
| ON (Lock) | 10 kΩ or higher | |
| Switch not operated | 10 kΩ or higher |
If the result is not as specified, replace the integration control and panel assembly (electric parking brake switch).
Inspect the illumination:
| *a | Component without harness connected
Integration Control and Panel Assembly (Electric Parking Brake Switch) |
Apply battery voltage to the integration control and panel assembly (electric parking brake switch) and check that the switch illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 12 (ILL+)
Battery negative (-) → Terminal 1 (ILL-) |
Illuminates |
If the result is not as specified, replace the integration control and panel assembly (electric parking brake switch).
84390A
2.INSPECT BRAKE WARNING SWITCH ASSEMBLY (ELECTRIC PARKING BRAKE SWITCH) (for Manual Transaxle)
Check the resistance.
| *a | Component without harness connected
Brake Warning Switch Assembly (Electric Parking Brake Switch) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (SWI1) - 8 (SWO1) | OFF (Release) | 10 kΩ or higher |
| ON (Lock) | Below 1 Ω | |
| Switch not operated | 10 kΩ or higher | |
| 7 (SWI1) - 1 (SWI2) | OFF (Release) | Below 1 Ω |
| ON (Lock) | Below 1 Ω | |
| Switch not operated | 10 kΩ or higher | |
| 7 (SWI1) - 2 (SWO2) | OFF (Release) | Below 1 Ω |
| ON (Lock) | 10 kΩ or higher | |
| Switch not operated | Below 1 Ω | |
| 1 (SWI2) - 8 (SWO1) | OFF (Release) | 10 kΩ or higher |
| ON (Lock) | Below 1 Ω | |
| Switch not operated | Below 1 Ω | |
| 1 (SWI2) - 2 (SWO2) | OFF (Release) | Below 1 Ω |
| ON (Lock) | 10 kΩ or higher | |
| Switch not operated | 10 kΩ or higher |
If the result is not as specified, replace the brake warning switch assembly.
Check the Illumination.
| *a | Component without harness connected
Brake Warning Switch Assembly |
Apply auxiliary battery voltage to the brake warning switch assembly and check that the switch illuminates.
| Condition | Specified Condition |
|---|---|
| Auxiliary battery positive (+) → 9 (ILL+)
Auxiliary battery negative (-) → 6 (ILL-) |
Illuminates |
If the result is not as specified, replace the brake warning switch assembly.