Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) D

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  OPERATION CHECK  


CHECK CUSTOMIZE PARAMETERS


NOTICE:

The operation check below is based on the non-customized initial condition of the vehicle.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>CUSTOMIZE PARAMETERS



CHECK PUSH-BUTTON START FUNCTION


a.

Get into the vehicle while carrying the electrical key transmitter sub-assembly with the power switch off. With the shift state park (P), check that the key indicator display is displayed when the brake pedal is depressed. Check that the hybrid control system starts when the power switch is pressed after the key indicator display is displayed in the combination meter assembly.


b.

While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the power switch is pressed with the brake pedal released: off → on (ACC) → on (IG) → off.


c.

With the shift state park (P), check that the steering lock operates when a door is opened.


d.
B522180C01
2.969,2.021 2.667,2.021 2.667,2.021 0.719,1.021 true 2.688,2.021 2.167,1.063 true 3.01,1.938 3.323,2.094 0.313,0.156 10 false *a
*a Inspection Point


Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>PARTS LOCATION

·

Perform this inspection for both inspection points.




e.
B522181C01
0.667,0.51 2.76,0.104 2.76,0.104 2.948,0.104 true 2.146,0.49 2.698,0.125 true 3.042,0.031 3.354,0.229 0.313,0.198 10 false *a
*a Inspection Point


Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (rear floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>PARTS LOCATION

·

Perform this inspection for both inspection points.




f.
B522182C01
2.229,0.823 2.448,0.25 true 1.563,1.75 2.438,0.229 2.438,0.229 2.979,0.229 true 3.052,0.156 3.365,0.313 0.313,0.156 10 false *a
*a Inspection Point


Check the push-button start function operation range for the luggage compartment. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (inside luggage compartment).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>PARTS LOCATION

·

Perform the inspection for both inspection points.





CHECK POWER SOURCE MODE CHANGING FUNCTION


a.

Check that the power source mode changes according to the chart below.

Shift Position Brake Pedal Power Source Mode when power switch Pressed
Park (P) selected Released Off → on (ACC) → on (IG) → off
Park (P) selected Depressed Off → hybrid control system starts
Park (P) selected Depressed On (ACC) → hybrid control system starts
Park (P) selected Depressed On (IG) → hybrid control system starts
Park (P) selected Released / Depressed On (READY) → off
Park (P) not selected Released On (ACC) → on (IG) → on (ACC)
Park (P) not selected Depressed Off → on (IG)
Park (P) not selected Depressed On (ACC) → on (IG)
Park (P) not selected Released / Depressed On (READY) → on (ACC)



CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION


a.

Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.


b.

Check that the entry and start system does not operate while in transmitter battery saving mode.

HINT:

To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.




CHECK ENTRY CANCEL FUNCTION


a.

Cancel the entry and start system and check that all the functions of the entry and start system no longer operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>CUSTOMIZE PARAMETERS

HINT:

While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless function, and the hybrid control system can be started by holding the electrical key transmitter sub-assembly near the power switch.




CHECK KEY DIAGNOSTIC MODE


HINT:
·

With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the buzzer.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



a.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

b.

Inspect the appropriate item according to the following table.

Tester Display Inspection Item
[CH1/CH2] Overhead + Driver Side*1 w/ Entry Function:

Front door outside handle assembly (electrical key antenna) (for Driver Door)


[CH1] Overhead + Driver Side*1
[CH2] Overhead + Driver Side*1
[CH1/CH2] Overhead + Passenger Side*2 w/ Entry Function:

Front door outside handle assembly (electrical key antenna) (for Front Passenger Door)


[CH1] Overhead + Passenger Side*2
[CH2] Overhead + Passenger Side*2
[CH1/CH2] Overhead + Front Room*3

No. 1 indoor electrical key antenna assembly (front floor)


[CH1] Overhead + Front Room*3
[CH2] Overhead + Front Room*3
[CH1/CH2] Overhead + Rear Room*4

No. 1 indoor electrical key antenna assembly (rear floor)


[CH1] Overhead + Rear Room*4
[CH2] Overhead + Rear Room*4
[CH1/CH2] Overhead + Back Door*5 w/ Entry Function:

Electrical key antenna (outside luggage compartment)


[CH1] Overhead + Back Door*5
[CH2] Overhead + Back Door*5
[CH1/CH2] Luggage + Back Door (inside)/Rear2*6

No. 1 indoor electrical key antenna assembly (inside luggage)


[CH1] Luggage + Back Door (inside)/Rear2*6
[CH2] Luggage + Back Door (inside)/Rear2*6
[CH1/CH2] Immobiliser Amp*7

Amplifier (power switch)


[CH1] Immobiliser Amp*7
[CH2] Immobiliser Amp*7

·

[CH1]: Channel 1 is set.

·

[CH2]: Channel 2 is set.

·

[CH1/CH2]: Channel 1 and 2 switch automatically at a specific interval*.

*: If the electrical key transmitter sub-assembly is detected with either channel 1 or 2, the buzzer sounds.



c.

Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the buzzer sounds.

HINT:

The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*4. For "Overhead + Rear Room"*4, the buzzer sounds in one long, continuous beep.



d.
for LHD:
B522169C01
2.229,0.906 2.542,1.063 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


for RHD:
B522170C01
1.406,0.927 1.719,1.083 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


*1: Front door outside handle assembly (for Driver Door)

HINT:
·

Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.

·

*2: Perform the same inspection for the front passenger door.




e.
B522180C01
2.969,2.021 2.667,2.021 2.667,2.021 0.719,1.021 true 2.688,2.021 2.167,1.063 true 3.01,1.938 3.323,2.094 0.313,0.156 10 false *a
*a Inspection Point


*3: No. 1 indoor electrical key antenna assembly (front floor)

HINT:

Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.



f.
B522181C01
0.667,0.51 2.76,0.104 2.76,0.104 2.948,0.104 true 2.146,0.49 2.698,0.125 true 3.042,0.031 3.354,0.229 0.313,0.198 10 false *a
*a Inspection Point


*4: No. 1 indoor electrical key antenna assembly (rear floor)

HINT:

Place the electrical key transmitter sub-assembly on the rear seat cushion.



g.
B522178C01
1.781,1.708 2.094,1.865 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


w/ Entry Function:

*5: Electrical key antenna (outside luggage compartment)

HINT:

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle as shown in the illustration.



h.
B522182C01
2.229,0.823 2.448,0.25 true 1.563,1.75 2.438,0.229 2.438,0.229 2.979,0.229 true 3.052,0.156 3.365,0.313 0.313,0.156 10 false *a
*a Inspection Point


*6: No. 1 indoor electrical key antenna assembly (inside luggage compartment)

HINT:

Place the electrical key transmitter sub-assembly on the luggage room floor.



i.
B522184C01
2.083,0.469 2.229,0.271 2.229,0.271 2.365,0.271 true 0.656,0.302 0.802,0.302 0.802,0.302 1.01,0.51 true 0.406,0.25 0.719,0.448 0.313,0.198 10 false *1 2.49,0.198 2.802,0.396 0.313,0.198 10 false *2
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly


*7: Amplifier (power switch)

HINT:

While facing the logo side of the electrical key transmitter sub-assembly toward the power switch, hold the transmitter near the power switch.