Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM3620E _53 Suspension _076850 TIRE PRESSURE MONITORING _0374400 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mode Status Tire pressure warning system mode NORMAL or TEST NORMAL: Normal mode
TEST: Test mode
-
Main Tire Number of main tire ID to be registered 4 or 5 4 or 5 displayed
·

4 displayed: w/o Full Size Spare Tire

·

5 displayed: w/ Full Size Spare Tire


2nd Tire Number of 2nd tire ID to be registered 4 or 5 4 or 5 displayed
·

4 displayed: w/o Full Size Spare Tire

·

5 displayed: w/ Full Size Spare Tire


Initialization Switch Tire pressure warning reset switch ON or OFF OFF: "OK" switch (steering pad switch assembly) off
ON: Steering pad switch assembly operated, "Set Pressure" selected on the multi-information display and "OK" switch (steering pad switch assembly) pressed and held
-
Sensor ID Status Status of ID selection Main or 2nd Status of ID selection -
Initialization Switch Info Tire pressure warning reset switch setting information WITHOUT or WITH WITH -
Sensor ID Switch Function Information on whether there is ID switching function or not Without or With Without: ID switching function is not equipped
With: ID switching function is equipped
-
Vehicle Speed Vehicle speed reading min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed Speed indicated on the combination meter assembly
Registered ID 1 Code Registered ID1 code min.: 0, max.: FFFFFFF*1 ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0, max.: FFFFFFF*1 ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0, max.: FFFFFFF*1 ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0, max.: FFFFFFF*1 ID No. registered for transmitter ID4 displayed -
Registered ID 5 Code Registered ID5 code min.: 0, max.: FFFFFFF*1 ID No. registered for transmitter ID5 displayed w/ Full Size Spare Tire
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*2
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*2

·

w/ Full Size Spare Tire


Threshold of Low-pressure (Lower Limit) Tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Specified tire pressure warning threshold lower limit displayed If N/A is displayed, data has not been received.*2
ID 1 Initial Threshold of Low-pressure ID1 initial threshold of low-pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization -
ID 2 Initial Threshold of Low-pressure ID2 initial threshold of low-pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization -
ID 3 Initial Threshold of Low-pressure ID3 initial threshold of low-pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization -
ID 4 Initial Threshold of Low-pressure ID4 initial threshold of low-pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization -
ID 5 Initial Threshold of Low-pressure ID5 initial threshold of low-pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization w/ Full Size Spare Tire
ID 1 Temperature in Tire ID1 temperature in tire min.: -40°C (-40°F)
max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
ID 2 Temperature in Tire ID2 temperature in tire min.: -40°C (-40°F)
max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
ID 3 Temperature in Tire ID3 temperature in tire min.: -40°C (-40°F)
max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
ID 4 Temperature in Tire ID4 temperature in tire min.: -40°C (-40°F)
max.: 215°C (419°F)
Actual tire temperature If -40°C (-40°F) is displayed, data has not been received.
ID 5 Temperature in Tire ID5 temperature in tire min.: -40°C (-40°F)
max.: 215°C (419°F)
Actual tire temperature
·

If -40°C (-40°F) is displayed, data has not been received.

·

w/ Full Size Spare Tire


Number of Trouble Code Number of stored DTCs min.: 0
max.: 255
0 -
HINT:

*1: Displayed only when the ID No. is not registered.

*2: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121 to C2124 (C2125: w/ Full Size Spare Tire).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121




PERFORM ACTIVE TEST


Using the GTS to perform Active Tests allows the relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


f.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Tire Pressure Warning System Indicator Tire pressure warning light OFF or ON -