Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR SPOILER
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377207 REAR SPOILER A

EXTERIOR PANELS / TRIM  REAR SPOILER  REASSEMBLY  


PROCEDURE

Hide 76087C 1.INSTALL REAR SIDE SPOILER PROTECTOR

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When installing a new rear side spoiler protector, heat the rear side spoiler LH using a heat light.



Standard:
Item Temperature
Rear Side Spoiler LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear side spoiler LH excessively.


a.

When reusing the rear side spoiler LH:

i.

Using a heat light, heat the rear side spoiler LH surface.


ii.

Remove any remaining double-sided tape from the rear side spoiler LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear side spoiler sub-assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear side spoiler LH surface.





b.
B525812C06
1.042,0.729 1.292,0.729 true 1.021,1.958 1.271,1.958 true 1.333,0.677 1.552,0.833 0.219,0.156 10 true *a 1.313,1.906 1.51,2.073 0.198,0.167 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear side spoiler LH on the installation area of the rear side spoiler protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear side spoiler protector has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear side spoiler protector trying not to touch the adhesional surface.


e.
B525813C02
0.938,2.083 1.021,2.26 1.021,2.26 1.188,2.26 true 0.979,0.583 1.083,0.375 1.083,0.375 1.25,0.375 true 1.281,0.302 1.51,0.469 0.229,0.167 10 true *a 1.26,2.167 1.438,2.344 0.177,0.177 10 true *a
*a Mark-off Line


Install the 2 rear side spoiler protectors in the position shown in the illustration.


Hide 76875 2.INSTALL REAR SPOILER NO. 4 PROTECTOR

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When installing a new rear spoiler No. 4 protector, heat the rear side spoiler LH using a heat light.



Standard:
Item Temperature
Rear Side Spoiler LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear side spoiler LH excessively.


a.

When reusing the rear side spoiler LH:

i.

Using a heat light, heat the rear side spoiler LH surface.


ii.

Remove any remaining double-sided tape from the rear side spoiler LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear side spoiler sub-assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear side spoiler LH surface.





b.
B525810C05
1.052,1.417 1.385,1.417 true 1.469,1.354 1.719,1.563 0.25,0.208 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear side spoiler LH on the installation area of the rear spoiler No. 4 protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 4 protector has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear spoiler No. 4 protector trying not to touch the adhesional surface.


e.
B525811C02
1.063,1.365 1.396,1.365 1.396,1.365 1.396,1.615 true 1.323,1.615 1.635,1.813 0.313,0.198 10 false *a
*a Mark-off Line


Install the rear spoiler No. 4 protector in the position shown in the illustration.


Hide 76873B 3.INSTALL REAR SPOILER NO. 2 PROTECTOR

HINT:

When installing a new rear spoiler No. 2 protector, heat the rear spoiler using a heat light.


Standard:
Item Temperature
Rear Spoiler 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear spoiler excessively.


a.

When reusing the rear spoiler:

i.

Using a heat light, heat the rear spoiler surface.


ii.

Remove any remaining double-sided tape from the rear spoiler.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear spoiler surface.





b.
B525801C07
0.75,3.125 0.583,3.125 0.583,3.125 0.583,2.875 true 0.75,0.729 0.75,0.563 true 2.667,0.719 2.667,0.552 true 2.677,3.135 2.844,3.135 2.844,3.135 2.844,2.885 true 2.469,3.063 2.656,3.229 0.188,0.167 10 true *a 0.792,3.052 0.99,3.208 0.198,0.156 10 true *a 2.604,0.75 2.813,0.927 0.208,0.177 10 true *a 0.667,0.76 0.875,0.917 0.208,0.156 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear spoiler on the installation area of the rear spoiler No. 2 protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 2 protector has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear spoiler No. 2 protector trying not to touch the adhesional surface.


e.
B525802C06
0.76,0.365 0.76,0.198 0.76,0.198 1.01,0.198 true 2.583,0.375 2.583,0.208 2.583,0.208 2.833,0.208 true 2.833,2.708 2.833,2.542 2.833,2.542 2.667,2.542 true 0.667,2.688 0.667,2.521 0.667,2.521 0.917,2.521 true 2.844,0.135 3.083,0.302 0.24,0.167 10 true *a 1.021,0.125 1.26,0.292 0.24,0.167 10 true *a 0.906,2.448 1.146,2.615 0.24,0.167 10 true *a 2.438,2.448 2.677,2.615 0.24,0.167 10 true *a
*a Mark-off Line


Install the 4 rear spoiler No. 2 protectors in the position shown in the illustration.


Hide 76872A 4.INSTALL REAR SPOILER NO. 1 PROTECTOR

HINT:

When installing a new rear spoiler No. 1 protector, heat the rear spoiler using a heat light.


Standard:
Item Temperature
Rear Spoiler 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear spoiler excessively.


a.

When reusing the rear spoiler:

i.

Using a heat light, heat the rear spoiler surface.


ii.

Remove any remaining double-sided tape from the rear spoiler.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear spoiler surface.





b.

for Type A:

i.
B525805C07
2.604,3.135 2.771,3.135 2.771,3.135 2.771,2.969 true 1.719,0.771 1.719,0.604 true 0.823,3.135 0.656,3.135 0.656,3.135 0.656,2.969 true 2.375,3.083 2.573,3.229 0.198,0.146 10 true *a 0.875,3.083 1.073,3.24 0.198,0.156 10 true *a 1.646,0.771 1.833,0.917 0.188,0.146 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear spoiler on the installation area of the rear spoiler No. 1 protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 1 protector has been attached.




ii.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iii.

Remove the release paper of a new rear spoiler No. 1 protector trying not to touch the adhesional surface.


iv.
B525806C05
0.583,2.708 0.583,2.542 0.583,2.542 0.917,2.542 true 2.719,2.719 2.719,2.552 2.719,2.552 3.052,2.552 true 1.5,0.583 1.5,0.75 1.5,0.75 1.833,0.75 true 0.938,2.427 1.135,2.594 0.198,0.167 10 true *a 3.052,2.448 3.25,2.615 0.198,0.167 10 true *a 1.833,0.667 2.094,0.833 0.26,0.167 10 true *a
*a Mark-off Line


Install the 3 rear spoiler No. 1 protectors in the position shown in the illustration.



c.

for Type B:

i.

Apply primer to the rear spoiler on the installation area of the rear spoiler No. 1 protector using a brush or felt.

B585298C05
2.708,0.5 2.906,0.438 false 2.552,3.5 2.646,3.302 false 2.521,0.469 2.833,0.667 0.313,0.198 10 false *a 2.448,3.51 2.76,3.708 0.313,0.198 10 false *a
*a Mark-off Line - -
V100144

Primer - -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 1 protector has been attached.




ii.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iii.

Remove the release paper of a new rear spoiler No. 1 protector trying not to touch the adhesional surface.


iv.

Install the 7 rear spoiler No. 1 protectors in the position shown in the illustration.

B585299C08
2.708,0.5 2.906,0.438 false 2.552,3.5 2.646,3.302 false 2.521,0.469 2.833,0.667 0.313,0.198 10 false *a 2.448,3.51 2.76,3.708 0.313,0.198 10 false *a
*a Mark-off Line - -




Hide 76874C 5.INSTALL REAR SPOILER NO. 3 PROTECTOR

HINT:

When installing a new rear spoiler No. 3 protector, heat the rear spoiler using a heat light.


Standard:
Item Temperature
Rear Spoiler 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear spoiler excessively.


a.

When reusing the rear spoiler:

i.

Using a heat light, heat the rear spoiler surface.


ii.

Remove any remaining double-sided tape from the rear spoiler.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear spoiler sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear spoiler surface.





b.
B525803C08
0.76,0.427 0.76,0.26 0.76,0.26 0.927,0.26 true 0.823,3.073 0.656,3.073 0.656,3.073 0.656,2.906 true 2.667,3.052 2.833,3.052 2.833,3.052 2.833,2.885 true 2.531,0.26 2.698,0.26 2.698,0.26 2.698,0.427 true 2.313,0.198 2.51,0.375 0.198,0.177 10 true *a 2.438,2.99 2.656,3.167 0.219,0.177 10 true *a 0.885,3.01 1.094,3.198 0.208,0.188 10 true *a 0.99,0.208 1.188,0.385 0.198,0.177 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear spoiler on the installation area of the rear spoiler No. 3 protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear spoiler No. 3 protector has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear spoiler No. 3 protector trying not to touch the adhesional surface.


e.
B525804C07
0.75,0.438 0.75,0.271 0.75,0.271 1,0.271 true 2.583,0.448 2.583,0.281 2.583,0.281 2.833,0.281 true 2.667,2.885 2.667,3.052 2.667,3.052 2.917,3.052 true 0.563,2.896 0.563,3.063 0.563,3.063 0.813,3.063 true 0.979,0.167 1.188,0.344 0.208,0.177 10 true *a 0.813,3 1.021,3.177 0.208,0.177 10 true *a 2.917,2.99 3.125,3.167 0.208,0.177 10 true *a 2.833,0.177 3.042,0.354 0.208,0.177 10 true *a
*a Mark-off Line


Install the 4 rear spoiler No. 3 protectors in the position shown in the illustration.


Hide 81935D 6.INSTALL CENTER STOP LIGHT CORD ASSEMBLY

Hide 81570 7.INSTALL CENTER STOP LIGHT ASSEMBLY