Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF RACK › 2018.10–2020.08
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377213 ROOF RACK A

EXTERIOR PANELS / TRIM  ROOF RACK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 63439E 1.INSTALL NO. 4 ROOF CARRIER SEAL LH

a.
B581306

Temporary install 2 new No. 4 roof carrier seals LH.


b.
B581302

Install the 2 nuts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not over tighten it.




Hide 63439A 2.INSTALL NO. 3 ROOF CARRIER SEAL LH

a.
B581305

Temporary install 2 new No. 3 roof carrier seals LH.


b.
B581300

Install the 2 nuts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not over tighten it.




Hide 75566D 3.INSTALL FRONT ROOF SIDE GARNISH PROTECTOR LH

a.

for Panoramic Moon Roof:

HINT:
·

Perform this procedure after installing the front roof side rail pad LH.

·

When installing the front roof side garnish protector LH, heat the front roof side garnish protector LH and front roof side garnish sub-assembly LH using a heat light.



Standard Value:
Part Temperature
Front Roof Side Garnish Sub-assembly LH 20 to 30°C (68 to 86°F)
Front Roof Side Garnish Protector LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front roof side garnish protector LH and front roof side garnish sub-assembly LH excessively.


i.

When reusing the front roof side garnish sub-assembly LH:

1.

Using a heat light, heat the front roof side garnish sub-assembly LH surface.

2.

Remove any remaining double-sided tape from the front roof side garnish sub-assembly LH.

3.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front roof side garnish protector LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.





ii.

Apply primer to the front roof side garnish sub-assembly LH on the installation area of the front roof side garnish protector LH using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front roof side garnish protector LH has been attached.




iii.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iv.

Using a heat light, heat the front roof side garnish sub-assembly LH and a new front roof side garnish protector LH.


v.

Remove the release paper from the front roof side garnish protector LH.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



vi.
B617045C01
0.698,0.646 0.823,0.302 0.823,0.302 1.063,0.302 true 1.875,0.792 2.354,1.615 2.354,1.615 2.615,0.792 true 1,1.5 1.156,1.698 0.156,0.198 10 false A 2.24,0.896 2.365,1.063 0.125,0.167 10 true B 2.281,1.646 2.594,1.844 0.313,0.198 10 false *a 1.125,0.229 1.438,0.427 0.313,0.198 10 false *1
*1 Front Roof Side Rail Pad LH
*a Mark-off Line


Install the front roof side garnish protector LH in the position shown in the illustration.

Standard Measurement:
Area Measurement
A 0 to 10 mm (0 to 0.394 in.)
B 3 mm (0.118 in.)


NOTICE:

The application strength of the front roof side garnish protector LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the front roof side garnish sub-assembly LH.




Hide 63474 4.INSTALL REAR ROOF RACK LEG LH

a.
B581382

Attach the clip and guide to install the rear roof rack leg LH.


b.

Install the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 63472 5.INSTALL FRONT ROOF RACK LEG LH

a.
B581308

Attach the clip and guide to install the front roof rack leg LH.


b.

Install the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 75634 6.INSTALL NO. 2 ROOF SIDE GARNISH LID LH

a.
B525999C02
0,0 0,0 false
V113147

Install in this Direction


w/o Roof Carrier:

i.

Attach the claw and install the No. 2 roof side garnish lid LH as shown in the illustration.



Hide 75632A 7.INSTALL NO. 1 ROOF SIDE GARNISH LID LH

a.
B525995C02
0,0 0,0 false
V113147

Install in this Direction


w/o Roof Carrier:

i.

Attach the claw and install the No. 1 roof side garnish lid LH as shown in the illustration.