Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR OUTSIDE MOULDING
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377219 FRONT DOOR OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR OUTSIDE MOULDING  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75392A 1.INSTALL NO. 1 OUTSIDE MOULDING RETAINER

a.
B525917

Install the No. 1 outside moulding retainer.


Hide 75793 2.INSTALL FRONT DOOR UPPER OUTSIDE MOULDING PAD

HINT:

When installing a new front door upper outside moulding pad, heat the front door lower outside moulding LH using a heat light.


Standard:
Item Temperature
Front Door Lower Outside Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front door lower outside moulding LH excessively.


a.

When reusing the front door lower outside moulding LH:

i.

Using a heat light, heat the front door lower outside moulding LH surface.


ii.

Remove any remaining double-sided tape from the front door lower outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front door upper outside moulding pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new front door lower outside moulding LH surface.





b.

Apply primer to the front door lower outside moulding LH on the installation area of the front door upper outside moulding pad using a brush or felt.

B523502C02
0,0 0,0 false
V100145

Primer - -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front door upper outside moulding pad has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new front door upper outside moulding pad trying not to touch the adhesional surface.


e.

Install the front door upper outside moulding pad as shown in the illustration.

B523503C02
6.26,2.042 6,2.333 6,2.333 5.698,2.073 true 0.885,1.854 0.969,2.063 0.969,2.063 1.052,1.865 true 0.896,2.115 1.125,2.302 0.229,0.188 10 true *a 5.948,2.344 6.146,2.5 0.198,0.156 10 true *a
*a Mark-off Line - -
V113147

Install in this Direction - -


HINT:

Make sure that the end of the front door upper outside moulding pad is between the mark-off lines