Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR OUTSIDE MOULDING
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377220 REAR DOOR OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR OUTSIDE MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 67858B 1.INSTALL REAR DOOR PANEL PROTECTOR LH

a.
B526340C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the rear door panel protector LH as shown in the illustration.


b.

Remove the protective tape.


c.
B526226C02
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the screw and clip.


Hide 67888J 2.INSTALL NO. 2 ACCESS PANEL WEATHERSTRIP LH

a.
B523514

Attach the clip and install the No. 2 access panel weatherstrip LH.


Hide 75062 3.INSTALL OUTSIDE MOULDING SET LH (for Off Road Package)

HINT:

When installing the outside moulding set LH, heat the rear door panel and outside moulding set LH using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Outside Moulding Set LH 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door panel and outside moulding set LH excessively.


a.

Clean the rear door panel surface.

i.

Using a heat light, heat the rear door panel surface.


ii.

Remove any remaining double-sided tape from the outside moulding set LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the outside moulding set LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.





b.

Remove the release paper from the face of the outside moulding set LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B526341C01
0.75,1.667 1.083,1.667 true 0.75,1.083 1.083,1.083 true 0.604,1.583 0.833,1.781 0.229,0.198 10 true *a 0.583,1 0.813,1.198 0.229,0.198 10 true *a
*a Double-sided Tape
V113147

Install in this Direction


Attach the clip and claw, double-sided tape to install the outside moulding set LH as shown in the illustration.


d.
B526210C01
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the screw and clip.


e.

Remove the protective tape.


Hide 75062 4.INSTALL OUTSIDE MOULDING SET LH (except Off Road Package)

a.
B523518C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and claw to install the outside moulding set LH as shown in the illustration.


b.

Remove the protective tape.


c.
B523515C02
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the screw and clip.


Hide 75078 5.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

a.
B523510C02
0.573,1.417 0.573,1 0.573,1 0.938,1 false 2.594,2.802 2.927,2.802 2.927,2.802 2.927,2.385 false 0.958,0.917 1.25,1.167 0.292,0.25 10 true (1) 2.417,2.708 2.615,2.948 0.198,0.24 10 true (2)
V113147

Install in this Direction


Attach the clip and install the rear door lower outside moulding sub-assembly LH in the order shown in the illustration.


b.

Remove the protective tape.


c.
B523506

Install the nut.


d.
B523505

Install the hole plug.


e.
B523507

Install the clip.


Hide 67874C 6.INSTALL REAR DOOR NO. 5 WEATHERSTRIP LH