Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
75768B
1.INSTALL REAR DOOR MOULDING PAD LH (for Off Road Package)
When installing a new rear door moulding pad LH, heat the rear door rear upper outside moulding LH using a heat light.
| Item | Temperature |
|---|---|
| Rear Door Rear Upper Outside Moulding LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear door rear upper outside moulding LH excessively.
When reusing the rear door rear upper outside moulding LH:
Using a heat light, heat the rear door rear upper outside moulding LH surface.
Remove any remaining double-sided tape from the rear door rear upper outside moulding LH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear door moulding pad LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear door rear upper outside moulding LH surface.
Apply primer to the rear door rear upper outside moulding LH on the installation area of the rear door moulding pad LH using a brush or felt.
|
Primer | - | - |
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear door moulding pad LH has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear door moulding pad LH trying not to touch the adhesional surface.
Install the rear door moulding pad LH in the position shown in the illustration.
| *a | Mark-off Line | - | - |
|
Install in this Direction | - | - |
| Area | Specified Condition |
|---|---|
| A | 1.0 mm (0.0394 in.) |
Make sure that the end of the rear door moulding pad LH is between the mark-off lines.
75798B
2.INSTALL REAR DOOR REAR OUTSIDE MOULDING PAD (except Off Road Package)
When installing a new rear door rear outside moulding pad, heat the rear door rear upper outside moulding LH using a heat light.
| Item | Temperature |
|---|---|
| Rear Door Rear Upper Outside Moulding LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear door rear upper outside moulding LH excessively.
When reusing the rear door rear upper outside moulding LH:
Using a heat light, heat the rear door rear upper outside moulding LH surface.
Remove any remaining double-sided tape from the rear door rear upper outside moulding LH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear door rear outside moulding pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear door rear upper outside moulding LH surface.
Apply primer to the rear door rear upper outside moulding LH on the installation area of the rear door rear outside moulding pad using a brush or felt.
|
Primer | - | - |
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear door rear outside moulding pad has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear door rear outside moulding pad trying not to touch the adhesional surface.
Install the rear door rear outside moulding pad in the position shown in the illustration.
| *a | Mark-off Line | - | - |
|
Install in this Direction | - | - |
Make sure that the end of the rear door rear outside moulding pad is between the mark-off lines.
75768B
3.INSTALL REAR DOOR MOULDING PAD LH (except Off Road Package)
When installing a new rear door moulding pad LH, heat the rear door rear upper outside moulding LH using a heat light.
| Item | Temperature |
|---|---|
| Rear Door Rear Upper Outside Moulding LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear door rear upper outside moulding LH excessively.
When reusing the rear door rear upper outside moulding LH:
Using a heat light, heat the rear door rear upper outside moulding LH surface.
Remove any remaining double-sided tape from the rear door rear upper outside moulding LH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear door moulding pad LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear door rear upper outside moulding LH surface.
Apply primer to the rear door rear upper outside moulding LH on the installation area of the rear door moulding pad LH using a brush or felt.
|
Primer | - | - |
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear door moulding pad LH has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear door moulding pad LH trying not to touch the adhesional surface.
Install the rear door moulding pad LH in the position shown in the illustration.
| *a | Mark-off Line | - | - |
|
Install in this Direction | - | - |
Make sure that the end of the rear door moulding pad LH is between the mark-off lines.
75392A
4.INSTALL NO. 1 OUTSIDE MOULDING RETAINER
Install the No. 1 outside moulding retainer.
75797C
5.INSTALL REAR DOOR UPPER OUTSIDE MOULDING PAD
When installing a new rear door upper outside moulding pad, heat the rear door lower outside moulding LH using a heat light.
| Item | Temperature |
|---|---|
| Rear Door Lower Outside Moulding LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear door lower outside moulding LH excessively.
When reusing the rear door lower outside moulding LH:
Using a heat light, heat the rear door lower outside moulding LH surface.
Remove any remaining double-sided tape from the rear door lower outside moulding LH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear door upper outside moulding pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear door lower outside moulding LH surface.
Apply primer to the rear door lower outside moulding LH on the installation area of the rear door upper outside moulding pad using a brush or felt.
|
Primer | - | - |
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear door upper outside moulding pad has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear door upper outside moulding pad trying not to touch the adhesional surface.
Install the rear door upper outside moulding pad in the position shown in the illustration.
| *a | Mark-off Line | - | - |
|
Install in this Direction | - | - |
Make sure that the end of the rear door upper outside moulding pad is between the mark-off lines.