Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Rear)
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377223 WHEEL OPENING MOULDING(for Rear) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Rear)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75897A 1.INSTALL NO. 3 MOULDING TAPE

HINT:

When installing a new No. 3 moulding tape, heat the quarter panel wheel opening moulding LH using a heat light.


Standard:
Item Temperature
Quarter Panel Wheel Opening Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the quarter panel wheel opening moulding LH:

i.

Using a heat light, heat the quarter panel wheel opening moulding LH.


ii.

Remove any remaining double-sided tape quarter panel wheel opening moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 3 moulding tape with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new quarter panel wheel opening moulding LH surface.





b.

Apply primer to the quarter panel wheel opening moulding LH on the installation area of the No. 3 moulding tape using a brush or felt.

B525761C02
0,0 0,0 false
V100145

Primer - -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the No. 3 moulding tape has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new No. 3 moulding tape trying not to touch the adhesional surface.


e.

Install the No. 3 moulding tape in the position shown in the illustration.

B525762C02
3.75,2.365 3.5,2.5 3.5,2.5 3.615,2.229 true 1.958,1.458 2.146,1.115 2.146,1.115 2.365,1.458 true 2.052,0.938 2.365,1.135 0.313,0.198 10 false *a 3.354,2.521 3.552,2.698 0.198,0.177 10 true *a
*a Mark-off Line - -
V113147

Install in this Direction - -


HINT:

Make sure that the end of the No. 3 moulding tape is between the mark-off lines.



Hide 75896A 2.INSTALL NO. 2 MOULDING TAPE

HINT:

When installing a new No. 2 moulding tape, heat the quarter panel wheel opening moulding LH using a heat light.


Standard:
Item Temperature
Quarter Panel Wheel Opening Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the quarter panel wheel opening moulding LH:

i.

Using a heat light, heat the quarter panel wheel opening moulding LH.


ii.

Remove any remaining double-sided tape quarter panel wheel opening moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 2 moulding tape with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new quarter panel wheel opening moulding LH surface.





b.

Apply primer to the quarter panel wheel opening moulding LH on the installation area of the No. 2 moulding tape using a brush or felt.

B525759C02
0,0 0,0 false
V100145

Primer - -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the No. 2 moulding tape has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new No. 2 moulding tape trying not to touch the adhesional surface.


e.

Install the No. 2 moulding tape in the position shown in the illustration.

B525760C02
3.406,1.771 3.323,1.49 3.323,1.49 3.49,1.76 true 2.427,1.802 2.417,1.594 2.417,1.594 2.469,1.792 true 2.302,1.427 2.615,1.625 0.313,0.198 10 false *a 3.219,1.323 3.531,1.521 0.313,0.198 10 false *a
*a Mark-off Line - -


HINT:

Make sure that the end of the No. 2 moulding tape is between the mark-off lines.



Hide 75895A 3.INSTALL NO. 1 MOULDING TAPE

HINT:

When installing a new No. 1 moulding tape, heat the quarter panel wheel opening moulding LH using a heat light.


Standard:
Item Temperature
Quarter Panel Wheel Opening Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the quarter panel wheel opening moulding LH:

i.

Using a heat light, heat the quarter panel wheel opening moulding LH.


ii.

Remove any remaining double-sided tape quarter panel wheel opening moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 1 moulding tape with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new quarter panel wheel opening moulding LH surface.





b.

Apply primer to the quarter panel wheel opening moulding LH on the installation area of the No. 1 moulding tape using a brush or felt.

B525757C03
0,0 0,0 false
V100145

Primer - -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the No. 1 moulding tape has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new No. 1 moulding tape trying not to touch the adhesional surface.


e.

Install the No. 1 moulding tape in the position shown in the illustration.

B525758C03
2.5,2.417 2.667,2.417 2.667,2.417 2.667,2.167 true 2.302,2.323 2.531,2.521 0.229,0.198 10 true *a
*a Mark-off Line - -


HINT:

Make sure that the end of the No. 1 moulding tape is between the mark-off lines.



Hide 75697 4.INSTALL NO. 2 BODY OUTSIDE MOULDING PAD (for Off Road Package)

HINT:

When installing a new No. 2 body outside moulding pad, heat the quarter outside moulding LH using a heat light.


Standard:
Item Temperature
Quarter Outside Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the quarter outside moulding LH:

i.

Using a heat light, heat the quarter outside moulding LH.


ii.

Remove any remaining double-sided tape quarter outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 2 body outside moulding pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new quarter outside moulding LH surface.





b.

Apply primer to the quarter outside moulding LH on the installation area of the No. 2 body outside moulding pad using a brush or felt.

B526297C02
0,0 0,0 false
V100145

Primer - -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the No. 2 body outside moulding pad has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new No. 2 body outside moulding pad trying not to touch the adhesional surface.


e.

Install the No. 2 body outside moulding pad in the position shown in the illustration.

B526298C03
3.042,1.938 3.448,1.917 3.448,1.917 3.365,2.292 true 3.479,1.781 3.646,1.958 0.167,0.177 10 true *a 5.563,0.5 5.729,0.677 0.167,0.177 10 false A
*a Mark-off Line - -
V113147

Install in this Direction - -


Standard:
Area Specified Condition
A 1.0 mm (0.0394 in.)


HINT:

Make sure that the end of the No. 2 body outside moulding pad is between the mark-off lines.



Hide 75696 5.INSTALL NO. 1 BODY OUTSIDE MOULDING PAD (except Off Road Package)

HINT:

When installing a new No. 1 body outside moulding pad, heat the quarter outside moulding LH using a heat light.


Standard:
Item Temperature
Quarter Outside Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the quarter outside moulding LH:

i.

Using a heat light, heat the quarter outside moulding LH.


ii.

Remove any remaining double-sided tape quarter outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 1 body outside moulding pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new quarter outside moulding LH surface.





b.

Apply primer to the quarter outside moulding LH on the installation area of the No. 1 body outside moulding pad using a brush or felt.

B526326C03
0,0 0,0 false
V100145

Primer - -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the No. 1 body outside moulding pad has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new No. 1 body outside moulding pad trying not to touch the adhesional surface.


e.

Install the No. 1 body outside moulding pad in the position shown in the illustration.

B526343C03
5.948,0.927 5.896,1.146 5.896,1.146 5.813,0.938 true 3.385,1.823 3.406,2.115 3.406,2.115 3.125,2.083 true 3.417,2.135 3.635,2.323 0.219,0.188 10 true *a 5.823,1.167 6.042,1.354 0.219,0.188 10 true *a
*a Mark-off Line - -
V113147

Install in this Direction - -


HINT:

Make sure that the end of the No. 1 body outside moulding pad is between the mark-off lines.