Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Rear)
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377223 WHEEL OPENING MOULDING(for Rear) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Rear)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75874 1.INSTALL QUARTER PANEL WHEEL OPENING MOULDING LH

HINT:

When installing the quarter panel wheel opening moulding LH, heat the vehicle body and quarter panel wheel opening moulding LH using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Quarter Panel Wheel Opening Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body and quarter panel wheel opening moulding LH excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any remaining double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the quarter panel wheel opening moulding LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.





b.

Remove the release paper from the face of the No. 3 moulding tape and No. 2 moulding tape and No. 1 moulding tape.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B525751C06
1.167,0.906 1.5,0.906 true 2.01,0.615 2.01,0.365 true 2.292,0.625 2.292,0.458 true 1.938,0.615 2.135,0.823 0.198,0.208 10 true *a 1.49,0.823 1.688,1.031 0.198,0.208 10 true *a 2.229,0.625 2.427,0.833 0.198,0.208 10 true *a
*a Double-sided Tape
V113147

Install in this Direction


Attach the clip and double-sided tape to install the quarter panel wheel opening moulding LH as shown in the illustration.

HINT:

Press the quarter panel wheel opening moulding LH firmly to install it.



d.

Install the clip.


Hide 75606A 2.INSTALL QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH (except Off Road Package)

a.
B525746C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the quarter outside moulding sub-assembly LH.


b.

Remove the protective tape.


c.
B525743C01
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the screw and 2 clips.


Hide 75606A 3.INSTALL QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH (for Off Road Package)

HINT:

When installing the quarter outside moulding sub-assembly LH, heat the vehicle body and quarter outside moulding sub-assembly LH using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Quarter Outside Moulding Sub-assembly LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body and quarter outside moulding sub-assembly LH excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any remaining double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the quarter outside moulding sub-assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until sufficiently removed it.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.





b.

Install the quarter outside moulding sub-assembly LH.

i.

Using a heat light, heat the vehicle body.


ii.

Remove the release paper from the face of the No. 1 body outside moulding pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.




c.
B525903C02
1.177,0.823 1.26,0.49 1.26,0.49 1.427,0.49 true 1.469,0.406 1.667,0.583 0.198,0.177 10 true *a
*a Double-sided Tape
V113147

Install in this Direction


Attach the guide and claw and clip and double-sided tape to install the quarter outside moulding sub-assembly LH.

HINT:

Press the quarter outside moulding sub-assembly LH firmly to install it.



d.

Remove the protective tape.


e.
B525898C01
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the screw and 2 clips.


Hide 65632B 4.INSTALL REAR WHEEL FRONT HOUSE PLATE LH