Use the following procedure to troubleshoot the lighting system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with ignition switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the CAN communication system is functioning normally.
for HV Model:
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
for Gasoline Model:
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
CAN communication system DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for HV Model:
for Gasoline Model:
Check for DTCs and note any codes that are output.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR
Body Electrical / Main Body / Trouble Codes.
Body Electrical / HL AutoLeveling / Trouble Codes.
Body Electrical / HL AutoLeveling (Sub) / Trouble Codes.
w/ Automatic High Beam System:
Body Electrical / Front Recognition Camera (Front Lighting Control) / Trouble Codes.
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR
Body Electrical / Main Body / Clear DTCs.
Body Electrical / HL AutoLeveling / Clear DTCs.
Body Electrical / HL AutoLeveling (Sub) / Clear DTCs.
w/ Automatic High Beam System:
Body Electrical / Front Recognition Camera (Front Lighting Control) / Clear DTCs.
Recheck for DTCs by simulating the operation indicated by the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR
Body Electrical / Main Body / Trouble Codes.
Body Electrical / HL AutoLeveling / Trouble Codes.
Body Electrical / HL AutoLeveling (Sub) / Trouble Codes.
w/ Automatic High Beam System:
Body Electrical / Front Recognition Camera (Front Lighting Control) / Trouble Codes.
| Result | Proceed to |
|---|---|
| Malfunction is duplicated but DTCs are not output (w/ Automatic High Beam System) | A |
| DTCs are output | B |
| Malfunction cannot be duplicated and DTCs are not output (w/ Automatic High Beam System) | C |
| DTCs are not output (w/o Automatic High Beam System) | D |
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
D
Refer to Vehicle Control History.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>VEHICLE CONTROL HISTORY
Check for vehicle control history and note any codes that are output.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| No vehicle control history is output | A |
| X2020 or X204D is output | B |
| Any vehicle control history other than X2020 and X204D is output | C |
A
B
C
Refer to Problem Symptoms Table.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Refer to Vehicle Control History.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>VEHICLE CONTROL HISTORY
Clear the vehicle control history.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Recheck for vehicle control history.
Check if any vehicle control history is output.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle control history is not output | A |
| Vehicle control history is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B