Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY › 2018.10–2019.02
RM3620E _52 Drivetrain _077759 DRIVE SHAFT / PROPELLER SHAFT _0377448 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL OUTBOARD JOINT BOOT

a.

Wrap the splines of the rear drive shaft outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C06
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Rear Drive Shaft Outboard Joint Shaft Assembly
*2 Rear No. 2 Drive Shaft Outboard Joint Boot Clamp LH
*3 Rear Drive Shaft Outboard Joint Boot LH
*4 Rear Drive Shaft Outboard Joint Boot Clamp LH
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the rear drive shaft outboard joint shaft assembly in the following order:

i.

Rear No. 2 drive shaft outboard joint boot clamp LH


ii.

Rear drive shaft outboard joint boot LH


iii.

Rear drive shaft outboard joint boot clamp LH



c.

Pack the joint portion of the rear drive shaft outboard joint shaft assembly and outboard joint boot with grease.

Standard Grease Capacity:
for Torque Vectoring Differential 50 to 60 g (1.77 to 2.11 oz.)
except Torque Vectoring Differential 37 to 47 g (1.31 to 1.65 oz.)



d.

Install the rear drive shaft outboard joint boot to the rear drive shaft outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the rear drive shaft outboard joint boot LH.

·

Keep the inside of the rear drive shaft outboard joint boot LH free of foreign matter.




Hide 42346E 2.INSTALL REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

CAUTION:
·
C331975

When installing the rear No. 2 drive shaft outboard joint boot clamp LH, do not perform the work without wearing protective gloves.

·

If work is performed without using protective gloves, injuries may occur.



a.
C277141

Using a screwdriver, install the rear No. 2 drive shaft outboard joint boot clamp LH as shown in the illustration.

NOTICE:

Be careful not to damage the outboard joint boot.



Hide 42346C 3.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

a.

Install the rear drive shaft outboard joint boot clamp LH onto the outboard joint boot.


b.
C277142C01
1.146,1.615 1.354,1.615 1.354,1.615 1.75,0.99 true 2.271,1.719 2.583,1.917 0.313,0.198 10 *a 2.188,0.083 2.5,0.281 0.313,0.198 10 *b 0.823,1.521 1.135,1.719 0.313,0.198 10 SST
*a Turn
*b Hold


Place SST onto the rear drive shaft outboard joint boot clamp LH.

SST
09521-24010  


c.

Tighten SST so that the rear drive shaft outboard joint boot clamp LH is pinched.

NOTICE:
·

Do not overtighten SST.

·

Be careful not to damage the outboard joint boot.




d.
C277143N01
1.75,1.375 2.177,1.865 2.177,1.865 2.365,1.865 true 2.417,1.75 2.875,1.948 0.458,0.198 10 SST

Using SST, measure the clearance of the rear drive shaft outboard joint boot clamp LH.

SST
09240-00021  

Standard Clearance:

1.2 mm (0.0472 in.) or less


NOTICE:

If the measured value exceeds the specified value, retighten the rear drive shaft outboard joint boot clamp LH.



Hide 42360D 4.INSTALL REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY LH

a.

Wrap the spline of the rear drive shaft outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274277C07
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Rear Drive Shaft Inboard Joint Boot Clamp LH
*2 Rear Drive Shaft Inboard Joint Boot LH
*3 Rear No. 2 Drive Shaft Inboard Joint Boot Clamp LH
*a Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the rear drive outboard joint shaft assembly LH in the following order.

i.

Rear drive shaft inboard joint boot clamp LH


ii.

Inboard joint boot


iii.

Rear No. 2 drive shaft inboard joint boot clamp LH



c.

Remove the protective tape from the rear drive outboard joint shaft assembly LH.


d.
C127694C02
1.927,1.188 2.083,1.833 2.083,1.833 1.365,1.531 true 2.083,1.833 2.25,1.833 false 2.313,1.729 3.042,1.896 0.729,0.167 10 *a
*a Matchmark


Align the matchmarks and place the beveled side of the tripod joint axial spline toward the rear drive outboard joint shaft assembly LH.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and hammer, tap the tripod joint onto the rear drive outboard joint shaft assembly LH.

NOTICE:
·

Do not tap the rollers.

·

Be sure to install the tripod joint in the correct direction.




f.
F045046

Using a snap ring expander, install a new snap ring.


g.

Pack the rear drive shaft inboard joint assembly LH and inboard joint boot with grease from the boot kit.

Standard Grease Capacity:
for Torque Vectoring Differential 93 to 103 g (3.29 to 3.63 oz.)
except Torque Vectoring Differential 88 to 98 g (3.11 to 3.45 oz.)



h.
C127646C05
1.833,0.833 1.833,0.25 true 2.167,0.396 2.167,0.25 2.167,0.25 1.417,0.25 true 1.188,0.167 1.5,0.365 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the rear drive shaft inboard joint assembly LH to the rear drive outboard joint shaft assembly LH.


Hide 5.INSTALL INBOARD JOINT BOOT

a.

Install the inboard joint boot to the rear drive shaft inboard joint assembly.


b.
C127699N04
1.438,1.521 1.656,1.74 0.219,0.219 10 (A)

Check that the 2 joint boots are not stretched or contracted when the rear drive shaft assembly is at the standard length.

Length (A):
Item Length
for Torque Vectoring Differential LH Side 623.25 mm (2.04 ft.)
RH Side 609.25 mm (2.00 ft.)
except Torque Vectoring Differential 754.1 mm (2.47 ft.)


NOTICE:

Keep the drive shaft assembly level during inspection.


If the boots are stretched or contracted, correct them.


Hide 42347E 6.INSTALL REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

C129501

a.

Using needle-nose pliers, install the rear No. 2 drive shaft inboard joint boot clamp LH as shown in the illustration.

NOTICE:

Be careful not to damage the inboard joint boot.



Hide 42347C 7.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the rear No. 2 drive shaft inboard joint boot clamp LH.