Home › Steering › STEERING COLUMN › STEERING HEATER SWITCH
RM3620E _55 Steering _076852 STEERING COLUMN _0377457 STEERING HEATER SWITCH G

STEERING COLUMN  STEERING HEATER SWITCH  INSPECTION  


PROCEDURE

Hide 84255 1.INSPECT STEERING HEATER SWITCH

a.
C406925C01
2.25,2 2.083,2 2.083,2 2,1.417 true 1.167,2 1.333,2 1.333,2 1.417,1.417 true 0.948,1.917 1.26,2.115 0.313,0.198 10 false IG 2.302,1.906 2.615,2.104 0.313,0.198 10 false B 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a
*a Component without harness connected
(Steering Heater Switch)


Remove the steering heater switch.

Click hereSteering>STEERING COLUMN>STEERING HEATER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IG) - 2 (B) Steering heater switch is pushed Below 1 Ω
5 (IG) - 2 (B) Steering heater switch is not pushed 10 kΩ or higher



c.
C406926C01
2.5,2.167 2.333,2.167 2.333,2.167 2.25,1.417 true 0.917,2.167 1.083,2.167 1.083,2.167 1.167,1.417 true 1.917,3.417 2.833,3.417 true 2.542,2.083 3.156,2.281 0.615,0.198 10 false +ILL 0.594,2.073 1.208,2.271 0.615,0.198 10 false +ILL 0.198,0.188 0.51,0.344 0.313,0.156 10 false *a 2.896,3.333 3.208,3.49 0.313,0.156 10 false *b
*a Component without harness connected
(Steering Heater Switch)
*b Indicator


Apply battery voltage to the connector and check the illumination conditions.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 6 (+ILL)
Battery negative (-) → 1 (-ILL)
Illuminates


If the result is not as specified, replace the steering heater switch.


Hide 85913F 2.INSPECT STEERING HEATER RELAY

a.
E256070N03
2.281,1.417 2.583,1.323 false 2.813,1.479 3.01,1.438 false 2.792,1.125 2.667,1 false 2.906,0.792 2.667,0.656 false 0.281,1.396 0.438,1.594 0.156,0.198 10 false 1 1.573,1.396 1.729,1.594 0.156,0.198 10 false 2 0.292,0.677 0.448,0.875 0.156,0.198 10 false 3 1.583,0.896 1.74,1.094 0.156,0.198 10 false 5 2.948,0.75 3.104,0.948 0.156,0.198 10 false 3 2.844,1.104 3,1.302 0.156,0.198 10 false 5 2.729,1.427 2.885,1.625 0.156,0.198 10 false 1 2.635,1.229 2.792,1.427 0.156,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminal 1 and 2 10 MΩ or higher
3 - 5 Battery voltage is applied to terminal 1 and 2 Below 1 Ω


If the result is not as specified, replace the steering heater relay.