Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
85110
1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (w/o Spring)
Do not touch the filter of waterproof cap.
When installing the windshield wiper motor assembly, check the waterproof cap filter for any cracks or damage and that there is no grease on it.
Do not reuse the windshield wiper motor assembly if it has been dropped or subjected to any strong impacts.
Install the 2 nuts.
Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 "TORX" bolts.
|
MP grease |
Apply MP grease to the windshield wiper motor crank pivot.
Install the No. 1 windshield wiper link rod so that the No. 1 windshield wiper link rod, windshield wiper motor crank pivot and windshield wiper motor assembly shaft are all aligned as shown in the illustration.
| *1 | No. 1 Windshield Wiper Link Rod | *2 | Windshield Wiper Motor Assembly Shaft |
| *3 | Windshield Wiper Motor Crank Pivot | - | - |
| *a | Straight Line | - | - |
85012A
2.INSTALL FRONT WIPER CRANK SUB-ASSEMBLY (w/ Spring)
Do not touch the filter of waterproof cap.
When installing the windshield wiper motor assembly, check the waterproof cap filter for any cracks or damage and that there is no grease on it.
Do not reuse the windshield wiper motor assembly if it has been dropped or subjected to any strong impacts.
| *a | Matchmark |
When reusing windshield wiper motor assembly and front wiper crank sub-assembly:
Align the windshield wiper motor assembly shaft and front wiper link sub-assembly matchmarks and install the front wiper crank sub-assembly with the nut.
| *a | Paint Mark |
|
Install in this Direction |
Mark the nut with paint as shown in the illustration.
Tighten the nut 115° as shown in the illustration.
| Area | Specified Condition |
|---|---|
| A | 115° |
| *a | Perpendicular line |
| *b | Parallel line |
When not reusing the windshield wiper motor assembly or front wiper crank sub-assembly:
Place the windshield wiper motor assembly horizontally around the windshield wiper motor shaft.
Install the front wiper crank sub-assembly with the nut at the position shown in the illustration.
| Area | Specified Condition |
|---|---|
| A | 70 to 85° |
| *a | Paint Mark |
|
Install in this Direction |
Mark the nut with paint as shown in the illustration.
Tighten the nut 115° as shown in the illustration.
| Area | Specified Condition |
|---|---|
| A | 115° |
85110
3.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (w/ Spring)
Install the 2 nuts.
Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 "TORX" bolts.
|
MP grease |
Apply MP grease to the front wiper crank pivot.
Install the No. 1 windshield wiper link rod so that the No. 1 windshield wiper link rod, front wiper crank pivot and windshield wiper motor assembly shaft are all aligned as shown in the illustration.
| *1 | No. 1 Windshield Wiper Link Rod | *2 | Windshield Wiper Motor Assembly Shaft |
| *3 | Front Wiper Crank Pivot | - | - |
| *a | Straight Line | - | - |
4.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
| *1 | Motor Grommet |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Attach the motor grommet and temporarily install the windshield wiper motor and link assembly as shown in the illustration.
Do not damage the vehicle with the front wiper motor and link assembly.
|
Bolt |
|
Connector |
Install the windshield wiper motor and link assembly with the 2 bolts in the order whown in the illustration.
Connect the connector.
55752
5.INSTALL COWL VENTILATOR SPLASH SHIELD
Perform this procedure only when replacement of the cowl ventilator splash shield is necessary.
|
Install in this Direction |
Temporarily install the cowl ventilator splash shield as shown in the illustration.
Attach the clip, claw and clamp to install the cowl ventilator splash shield.
Connect the connector.
53383
6.INSTALL HOOD TO COWL TOP SEAL
Perform this procedure only when replacement of the hood to cowl top seal is necessary.
Attach the clip and install the hood to cowl top seal.
55708
7.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Temporarily install the cowl top ventilator louver sub-assembly as shown in the illustration.
| *a | Positioning Guide | *b | Cutout |
|
Install in this Direction | - | - |
Align the positioning guide of the cowl top ventilator louver sub-assembly to the front window inner center moulding cutout.
Attach the guide.
Hold the rear of the cowl top ventilator louver sub-assembly down and attach the cowl top ventilator louver sub-assembly to the front window inner center moulding.
|
Install in this Direction | - | - |
Check that the cowl top ventilator louver sub-assembly does not lift up.
Check that the positioning guide is not pinched by the front window inner center moulding.
Install the cowl top ventilator louver sub-assembly with the 2 clips.
53867H
8.INSTALL FRONT FENDER TO COWL SIDE SEAL LH
|
Install in this Direction |
Attach the claw as shown in the illustration.
|
Install in this Direction |
Attach the guide as shown in the illustration.
|
Install in this Direction |
Attach the claw in the direction indicated by the arrow as shown in the illustration.
Make sure that the claw is securely attached.
Attach the guide to install the front fender to cowl side seal LH as shown in the illustration.
Remove the protective tape.
53866J
9.INSTALL FRONT FENDER TO COWL SIDE SEAL RH
Use the same procedure described for the LH side.
10.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
| *a | Windshield Wiper Arm Serrations |
| *b | Windshield Wiper Motor Assembly Pivot Serrations |
When reusing the windshield wiper arm and blade assembly RH:
Clean the windshield wiper arm serrations.
Do not grind the windshield wiper arm serrations.
When reusing the windshield wiper motor assembly:
Using a wire brush, clean the windshield wiper motor assembly pivot serrations.
Do not grind the windshield wiper motor assembly pivot serrations.
Turn the ignition switch to ON.
Operate the windshield wiper motor assembly and stop at the automatic stop (park) position.
Turn the ignition switch off.
| *a | Ceramic Notch |
Align the ceramic notch of the windshield glass sub-assembly with the edge of the windshield wiper arm and blade assembly RH to install the windshield wiper arm and blade assembly RH with the nut.
| Area | Measurement |
|---|---|
| A | 10 mm (0.394 in.) |
Hold the windshield wiper arm by hand while tightening the nut.
Turn the ignition switch to ON.
Operate the windshield wiper while spraying washer fluid onto the windshield glass. Make sure that the windshield wiper functions properly and the wiper does not come into contact with the vehicle body.
Turn the ignition switch off.
Raise the windshield wiper arm 2 times and check that the tip of the windshield wiper blade is within the range shown in the illustration.
11.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
| *a | Windshield Wiper Arm Serrations |
| *b | Windshield Wiper Motor Assembly Pivot Serrations |
When reusing the windshield wiper arm and blade assembly LH:
Clean the windshield wiper arm serrations.
Do not grind the windshield wiper arm serrations.
When reusing the windshield wiper motor assembly:
Using a wire brush, clean the windshield wiper motor assembly pivot serrations.
Do not grind the windshield wiper motor assembly pivot serrations.
Turn the ignition switch to ON.
Operate the windshield wiper motor assembly and stop at the automatic stop (park) position.
Turn the ignition switch off.
| *a | Ceramic Notch |
Align the ceramic notch of the windshield glass sub-assembly with the edge of the windshield wiper arm and blade assembly LH to install the windshield wiper arm and blade assembly LH with the nut.
| Area | Measurement |
|---|---|
| A | 10 mm (0.394 in.) |
Hold the windshield wiper arm by hand while tightening the nut.
Turn the ignition switch to ON.
Operate the windshield wiper while spraying washer fluid onto the windshield glass. Make sure that the windshield wiper functions properly and the wiper does not come into contact with the vehicle body.
Turn the ignition switch off.
Raise the windshield wiper arm 2 times and check that the tip of the windshield wiper blade is within the range shown in the illustration.
85292B
12.INSTALL FRONT WIPER ARM HEAD CAP
Attach the claw and install the front wiper arm head cap.
Use the same procedure for the RH and LH sides.