Home › Vehicle Interior › SEAT › SEAT MEMORY SWITCH
RM3620E _58 Vehicle Interior _076405 SEAT _0377511 SEAT MEMORY SWITCH G

SEAT  SEAT MEMORY SWITCH  INSPECTION  


PROCEDURE

Hide 84927 1.INSPECT SEAT MEMORY SWITCH (for LHD)

a.

Check the resistance.

i.
B521475C01
1.042,2.865 1.406,2.865 true 1.979,2.865 2.344,2.865 true 1.531,3.167 1.615,2.927 true 1.875,3.177 1.792,2.927 true 1.458,3.188 1.615,3.385 0.156,0.198 10 false 1 0.948,2.781 1.104,2.979 0.156,0.198 10 false 2 1.74,3.198 2.24,3.406 0.5,0.208 10 false MMRY 2.417,2.802 2.698,3.052 0.281,0.25 10 false E 0.75,2.094 1.063,2.25 0.313,0.156 10 false *a
*a Component without harness connected
(Seat Memory Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the seat memory switch.

3 (1) - 1 (E) 1 switch pressed Below 1 Ω
3 (1) - 1 (E) 1 switch not pressed 10 kΩ or higher
4 (2) - 1 (E) 2 switch pressed Below 1 Ω
4 (2) - 1 (E) 2 switch not pressed 10 kΩ or higher
2 (MMRY) - 1 (E) SET switch pressed Below 1 Ω
2 (MMRY) - 1 (E) SET switch not pressed 10 kΩ or higher




Hide 84927 2.INSPECT SEAT MEMORY SWITCH (for RHD)

a.

Check the resistance.

i.
B529751C04
1.042,2.865 1.406,2.865 true 1.979,2.865 2.344,2.865 true 1.531,3.167 1.615,2.927 true 1.875,3.177 1.792,2.927 true 1.427,3.188 1.646,3.396 0.219,0.208 10 false M1 0.813,2.781 1.063,3 0.25,0.219 10 false M2 1.74,3.198 2.24,3.406 0.5,0.208 10 false MRY 2.417,2.802 2.698,3.052 0.281,0.25 10 false E 0.75,2.094 1.063,2.25 0.313,0.156 10 false *a
*a Component without harness connected
(Seat Memory Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the seat memory switch.

3 (M1) - 1 (E) 1 switch pressed Below 1 Ω
3 (M1) - 1 (E) 1 switch not pressed 10 kΩ or higher
4 (M2) - 1 (E) 2 switch pressed Below 1 Ω
4 (M2) - 1 (E) 2 switch not pressed 10 kΩ or higher
2 (MRY) - 1 (E) SET switch pressed Below 1 Ω
2 (MRY) - 1 (E) SET switch not pressed 10 kΩ or higher