75741E
1.INSTALL SYMBOL EMBLEM
When installing a new symbol emblem, heat the back door outside garnish sub-assembly and symbol emblem using a heat light.
| Item | Temperature |
|---|---|
| Back Door Outside Garnish Sub-assembly | 20 to 30°C (68 to 86°F) |
| Symbol Emblem | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the back door outside garnish sub-assembly and symbol emblem excessively.
Clean the back door outside garnish sub-assembly surface.
Using a heat light, heat the back door outside garnish sub-assembly surface.
Remove any remaining double-sided tape from the back door outside garnish sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Installing the symbol emblem with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Using a heat light, heat the back door outside garnish sub-assembly and a new symbol emblem.
Remove the release paper from the symbol emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
for Gasoline Model:
| *a | Boss Position |
Align the boss positions and install the symbol emblem.
Press the symbol emblem firmly to install it.
for HV Model:
| *a | Boss Position |
Align the boss positions and install the symbol emblem.
Press the symbol emblem firmly to install it.
75441E
2.INSTALL BACK DOOR NO. 1 NAME PLATE
When installing a new back door No. 1 name plate, heat the back door panel and back door No. 1 name plate using a heat light.
| Item | Temperature |
|---|---|
| Back Door Panel | 40 to 60°C (104 to 140°F) |
| Back Door No. 1 Name Plate | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the back door panel and back door No. 1 name plate excessively.
Clean the back door panel surface.
Using a heat light, heat the back door panel surface.
Remove any remaining double-sided tape from the back door panel.
Wipe off any tape adhesive residue with cleaner.
Installing the back door No. 1 name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Using a heat light, heat the back door panel and a new back door No. 1 name plate.
Remove the release paper from the back door No. 1 name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the back door No. 1 name plate as shown in the illustration.
Press the back door No. 1 name plate firmly to install it.
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 37.5 mm (1.48 in.) | B | 42.7 mm (1.68 in.) |
| C | 164.9 mm (6.49 in.) | D | 125.0 mm (4.92 in.) |
| E | 122.3 mm (4.81 in.) | - | - |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 166.6 mm (6.56 in.) | B | 18.4 mm (0.724 in.) |
| C | 27.9 mm (1.10 in.) | D | 123.7 mm (4.87 in.) |
| E | 119.3 mm (4.70 in.) | - | - |
75443
3.INSTALL BACK DOOR NO. 3 NAME PLATE
When installing a new back door No. 3 name plate, heat the back door panel and back door No. 3 name plate using a heat light.
| Item | Temperature |
|---|---|
| Back Door Panel | 40 to 60°C (104 to 140°F) |
| Back Door No. 3 Name Plate | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the back door panel and back door No. 3 name plate excessively.
Clean the back door panel surface.
Using a heat light, heat the back door panel surface.
Remove any remaining double-sided tape from the back door panel.
Wipe off any tape adhesive residue with cleaner.
Installing the back door No. 3 name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Using a heat light, heat the back door panel and a new back door No. 3 name plate.
Remove the release paper from the back door No. 3 name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the back door No. 3 name plate as shown in the illustration.
Press the back door No. 3 name plate firmly to install it.
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 16.7 mm (0.657 in.) | B | 24.1 mm (0.949 in.) |
| C | 172.6 mm (6.80 in.) | D | 122.7 mm (4.83 in.) |
| E | 120.7 mm (4.75 in.) | - | - |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 65.2 mm (2.57 in.) | B | 125.6 mm (4.94 in.) |
| C | 122.4 mm (4.82 in.) | D | 121.1 mm (4.77 in.) |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 53.0 mm (2.09 in.) | B | 149.0 mm (5.87 in.) |
| C | 122.9 mm (4.84 in.) | D | 120.9 mm (4.76 in.) |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 27.5 mm (1.08 in.) | B | 169.9 mm (6.69 in.) |
| C | 124.7 mm (4.91 in.) | D | 121.0 mm (4.76 in.) |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 168.9 mm (6.65 in.) | B | 18.1 mm (0.713 in.) |
| C | 5.4 mm (0.213 in.) | D | 122.6 mm (4.83 in.) |
| E | 118.5 mm (4.67 in.) | - | - |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 56.3 mm (2.22 in.) | B | 143.9 mm (5.67 in.) |
| C | 125.1 mm (4.93 in.) | D | 123.1 mm (4.85 in.) |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 30.1 mm (1.19 in.) | B | 34.6 mm (1.36 in.) |
| C | 122.8 mm (4.83 in.) | D | 121.4 mm (4.78 in.) |
75444A
4.INSTALL BACK DOOR NO. 4 NAME PLATE
When installing a new back door No. 4 name plate, heat the back door panel and back door No. 4 name plate using a heat light.
| Item | Temperature |
|---|---|
| Back Door Panel | 40 to 60°C (104 to 140°F) |
| Back Door No. 4 Name Plate | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the back door panel and back door No. 4 name plate excessively.
Clean the back door panel surface.
Using a heat light, heat the back door panel surface.
Remove any remaining double-sided tape from the back door panel.
Wipe off any tape adhesive residue with cleaner.
Installing the back door No. 4 name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Using a heat light, heat the back door panel and a new back door No. 4 name plate.
Remove the release paper from the back door No. 4 name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the back door No. 4 name plate as shown in the illustration.
Press the back door No. 4 name plate firmly to install it.
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 59.0 mm (2.32 in.) | B | 139.1 mm (5.48 in.) |
| C | 93.2 mm (3.67 in.) | D | 91.1 mm (3.59 in.) |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 58.5 mm (2.30 in.) | B | 119.0 mm (4.69 in.) |
| C | 93.6 mm (3.69 in.) | D | 91.2 mm (3.59 in.) |
| *a | Reference Values | *b | Back Door Edge Line |
| *c | Back Door Lower Outside Garnish Sub-assembly Upper Side Edge | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 33.8 mm (1.33 in.) | B | 37.1 mm (1.46 in.) |
| C | 92.9 mm (3.66 in.) | D | 91.5 mm (3.60 in.) |
75362
5.INSTALL FRONT FENDER NO. 2 NAME PLATE
When installing a new front fender No. 2 name plate, heat the fender panel and front fender No. 2 name plate using a heat light.
| Item | Temperature |
|---|---|
| Fender Panel | 40 to 60°C (104 to 140°F) |
| Front Fender No. 2 Name Plate | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the fender panel and front fender No. 2 name plate excessively.
Clean the fender panel surface.
Using a heat light, heat the fender panel surface.
Remove any remaining double-sided tape from the fender panel.
Wipe off any tape adhesive residue with cleaner.
Installing the front fender No. 2 name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Using a heat light, heat the fender panel and a new front fender No. 2 name plate.
Remove the release paper from the front fender No. 2 name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the front fender No. 2 name plate as shown in the illustration.
Press the front fender No. 2 name plate firmly to install it.
| *a | Reference Values | *b | Lower Side Baseline |
| *c | Front Fender Edge Line | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 200 mm (7.87 in.) | B | 18.5 mm (0.726 in.) |
| C | 35.2 mm (1.39 in.) | D | 43.2 mm (1.70 in.) |
| E | 56.8 mm (2.23 in.) | F | 37.4 mm (1.47 in.) |
| G | 41.2 mm (1.62 in.) | - | - |
75361A
6.INSTALL FRONT FENDER NO. 1 NAME PLATE
When installing a new front fender No. 1 name plate, heat the fender panel and front fender No. 1 name plate using a heat light.
| Item | Temperature |
|---|---|
| Fender Panel | 40 to 60°C (104 to 140°F) |
| Front Fender No. 1 Name Plate | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the fender panel and front fender No. 1 name plate excessively.
Clean the fender panel surface.
Using a heat light, heat the fender panel surface.
Remove any remaining double-sided tape from the fender panel.
Wipe off any tape adhesive residue with cleaner.
Installing the front fender No. 1 name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Using a heat light, heat the fender panel and a new front fender No. 1 name plate.
Remove the release paper from the front fender No. 1 name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the front fender No. 1 name plate as shown in the illustration.
Press the front fender No. 1 name plate firmly to install it.
| *a | Reference Values | *b | Lower Side Baseline |
| *c | Front Fender Edge Line | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 200 mm (7.87 in.) | B | 20.7 mm (0.815 in.) |
| C | 32.7 mm (1.29 in.) | D | 43.5 mm (1.71 in.) |
| E | 57.9 mm (2.28 in.) | F | 34.9 mm (1.37 in.) |
| G | 38.0 mm (1.50 in.) | - | - |