Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BACK DOOR OUTSIDE GARNISH (for Lower Side)
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377758 BACK DOOR OUTSIDE GARNISH(for Lower Side) A

EXTERIOR PANELS / TRIM  BACK DOOR OUTSIDE GARNISH(for Lower Side)  REASSEMBLY  


PROCEDURE

Hide 76882B 1.INSTALL BACK DOOR LOWER MOULDING PROTECTOR LH

HINT:
·

When installing a new back door lower moulding protector LH, heat the back door lower outside garnish using a heat light.

·

Use the same procedure to install the back door lower moulding protector LH on the other side.



Standard:
Item Temperature
Back Door Lower Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the back door lower outside garnish:

i.

Using a heat light, heat the back door lower outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door lower outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door lower moulding protector LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new back door lower outside garnish surface.





b.
B524056C01
0,0 0,0 false
V100144

Primer


Apply primer to the back door lower outside garnish on the installation area of the back door lower moulding protector LH using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the back door lower moulding protector LH has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new back door lower moulding protector LH trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.
B524057C02
1.063,4.042 0.583,3.865 false 0.865,0.917 1.135,1.26 true 0.479,4.135 0.792,4.333 0.313,0.198 10 false *a 2.771,4.135 3.083,4.333 0.313,0.198 10 false *a 1.073,4.021 1.385,4.219 0.313,0.198 10 false *b 1.198,1.208 1.406,1.417 0.208,0.208 10 true *c
*a 2.0 mm (0.0787 in.)
*b Application Start Position
*c Mark-off Line


Align the back door lower moulding protector LH with the application start position and install it.

HINT:

Press the back door lower moulding protector LH firmly to install it.



Hide 76822A 2.INSTALL BACK DOOR LOWER GARNISH MOULDING PROTECTOR

HINT:
·

When installing a new back door lower garnish moulding protector, heat the back door lower outside garnish using a heat light.

·

Use the same procedure to install the back door lower garnish moulding protector on the other side.



Standard:
Item Temperature
Back Door Lower Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the back door lower outside garnish:

i.

Using a heat light, heat the back door lower outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door lower outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door lower garnish moulding protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new back door lower outside garnish surface.





b.
B524058C01
0,0 0,0 false
V100144

Primer


Apply primer to the back door lower outside garnish on the installation area of the back door lower garnish moulding protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the back door lower garnish moulding protector has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new back door lower garnish moulding protector trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.
B524059C01
2.083,4.083 2.563,3.969 false 0.948,1.229 0.833,0.865 true 0.708,4.292 1.021,4.49 0.313,0.198 10 false *a 2.573,4.292 2.885,4.49 0.313,0.198 10 false *a 1.885,3.99 2.083,4.188 0.198,0.198 10 false *b 0.917,1.25 1.229,1.448 0.313,0.198 10 false *c
*a 2.0 mm (0.0787 in.)
*b Application Start Position
*c Mark-off Line


Align the back door lower garnish moulding protector with the application start position and install it.

HINT:

Press the back door lower garnish moulding protector firmly to install it.



Hide 76881B 3.INSTALL BACK DOOR LOWER MOULDING PROTECTOR RH

HINT:
·

When installing a new back door lower moulding protector RH, heat the back door lower outside garnish using a heat light.

·

Use the same procedure to install the back door lower moulding protector RH on the other side.



Standard:
Item Temperature
Back Door Lower Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the back door lower outside garnish:

i.

Using a heat light, heat the back door lower outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door lower outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door lower moulding protector RH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new back door lower outside garnish surface.





b.
B524060C01
0,0 0,0 false
V100144

Primer


Apply primer to the back door lower outside garnish on the installation area of the back door lower moulding protector RH using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the back door lower moulding protector RH has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new back door lower moulding protector RH trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.
B524061C01
2.792,1.146 2.188,0.875 true 2.417,0.698 2.844,0.448 true 0.896,4.271 1.115,4.469 0.219,0.198 10 false *a 2.896,0.333 3.208,0.531 0.313,0.198 10 false *b 2.865,1.104 3.177,1.302 0.313,0.198 10 false *c
*a 2.0 mm (0.0787 in.)
*b Application Start Position
*c Mark-off Line


Align the back door lower moulding protector RH with the application start position and install it.

HINT:

Press the back door lower moulding protector RH firmly to install it.



Hide 76821 4.INSTALL BACK DOOR UPPER GARNISH MOULDING PROTECTOR

HINT:

When installing a new back door upper garnish moulding protector, heat the back door lower outside garnish using a heat light.


Standard:
Item Temperature
Back Door Lower Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the back door lower outside garnish:

i.

Using a heat light, heat the back door lower outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door lower outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door upper garnish moulding protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new back door lower outside garnish surface.





b.

Apply primer to the back door lower outside garnish on the installation area of the back door upper garnish moulding protector using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the back door upper garnish moulding protector has been attached.



B524062C02
0,0 0,0 false
V100144

Primer - -



c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new back door upper garnish moulding protector trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.

Align the back door upper garnish moulding protector with the application start position and install it to fit in the mark-off line range.

HINT:

Press the back door upper garnish moulding protector firmly to install it.


B524063C01
1.302,3.417 1.583,3.5 true 5.688,2.771 6.031,2.896 false 0.906,2.5 1.146,2.719 0.24,0.219 10 false *a 1.646,3.438 1.823,3.635 0.177,0.198 10 false *c 6.021,2.49 6.26,2.708 0.24,0.219 10 false *a 5.531,2.667 5.771,2.885 0.24,0.219 10 false *b
*a 3.0 mm (0.118 in.) *b Application Start Position
*c Mark-off Line - -