INSPECT DRIVER SEAT BELT WARNING LIGHT (w/ Buzzer Regulated by Law)
The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.
Turn the ignition switch off.
Turn the ignition switch to ON.
When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.
Check that the seat belt warning light on the combination meter assembly changes from blinking to turns off.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.
Check that the seat belt warning light (in the combination meter assembly) blinks when the driver seat belt is unfastened, the shift position is not in P and the parking brake is released.
Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the driver seat belt unfastened.
Check that after 96 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.
Check that the seat belt warning light (in the combination meter assembly) turns off when the driver seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.
INSPECT DRIVER SEAT BELT WARNING LIGHT (w/o Buzzer Regulated by Law, for Type A)
The warning lighting time differs depending on the specification, so they are listed as "Type A" and "Type B".
The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.
Turn the ignition switch to ON.
Check that the seat belt warning light (in the combination meter assembly) turns on with the driver seat belt unfastened and under any of the following conditions.
Shift position in P.
The parking brake is not released.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.
Check that the seat belt warning light (in the combination meter assembly) blinks when the driver seat belt is unfastened, the shift position is not in P and the parking brake is released.
Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the driver seat belt unfastened.
Check that after 120 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.
Check that the seat belt warning light (in the combination meter assembly) turns off when the driver seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.
INSPECT DRIVER SEAT BELT WARNING LIGHT (w/o Buzzer Regulated by Law, for Type B)
The warning lighting time differs depending on the specification, so they are listed as "Type A" and "Type B".
The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.
Turn the ignition switch to ON.
Check that the seat belt warning light (in the combination meter assembly) turns on with the driver seat belt unfastened and under any of the following conditions.
Shift position in P.
The parking brake is not released.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.
Check that the seat belt warning light (in the combination meter assembly) blinks when the driver seat belt is unfastened, the shift position is not in P and the parking brake is released.
Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the driver seat belt unfastened.
Check that after 124 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.
Check that the seat belt warning light (in the combination meter assembly) turns off when the driver seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.
INSPECT PASSENGER SEAT BELT WARNING LIGHT (w/ Buzzer Regulated by Law)
The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.
Turn the ignition switch to ON.
Check that the seat belt warning light (in the combination meter assembly) turns on with a passenger seated in the passenger seat, the passenger seat belt unfastened and under any of the following conditions.
Change the shift position to P.
The parking brake is not released.
Fasten the driver seat belt.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Place a load of 20 kg (44.1 lb) on the passenger seat.
When placing the load on the passenger seat, do not let it touch the seatback.
Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.
Check that the seat belt warning light (in the combination meter assembly) blinks when the passenger seat belt is unfastened, the shift position is not in P and the parking brake is released.
Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the passenger seat belt unfastened.
Check that after 96 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.
Check that the seat belt warning light (in the combination meter assembly) turns off when the passenger seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.
INSPECT PASSENGER SEAT BELT WARNING LIGHT (w/o Buzzer Regulated by Law, for Type A)
The warning lighting time differs depending on the specification, so they are listed as "Type A" and "Type B".
The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.
Turn the ignition switch to ON.
Check that the seat belt warning light (in the combination meter assembly) turns on with a passenger seated in the passenger seat, the passenger seat belt unfastened and under any of the following conditions.
Change the shift position to P.
The parking brake is not released.
Fasten the driver seat belt.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Place a load of 20 kg (44.1 lb) on the passenger seat.
When placing the load on the passenger seat, do not let it touch the seatback.
Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.
Check that the seat belt warning light (in the combination meter assembly) blinks when the passenger seat belt is unfastened, the shift position is not in P and the parking brake is released.
Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the passenger seat belt unfastened.
Check that after 120 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.
Check that the seat belt warning light (in the combination meter assembly) turns off when the passenger seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.
INSPECT PASSENGER SEAT BELT WARNING LIGHT (w/o Buzzer Regulated by Law, for Type B)
The warning lighting time differs depending on the specification, so they are listed as "Type A" and "Type B".
The seat belt warning light (in the combination meter assembly) is for both the driver seat and the passenger seat.
Turn the ignition switch to ON.
Check that the seat belt warning light (in the combination meter assembly) turns on with a passenger seated in the passenger seat, the passenger seat belt unfastened and under any of the following conditions.
Change the shift position to P.
The parking brake is not released.
Fasten the driver seat belt.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Place a load of 20 kg (44.1 lb) on the passenger seat.
When placing the load on the passenger seat, do not let it touch the seatback.
Check the status of the seat belt warning light (in the combination meter assembly) under the conditions below.
Check that the seat belt warning light (in the combination meter assembly) blinks when the passenger seat belt is unfastened, the shift position is not in P and the parking brake is released.
Check that the seat belt warning light (in the combination meter assembly) blinks when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the passenger seat belt unfastened.
Check that after 124 seconds, the seat belt warning light (in the combination meter assembly) changes from blinking to on.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the shift position is changed to P.
Check that the seat belt warning light (in the combination meter assembly) changes to on when the seat belt warning light (in the combination meter assembly) is blinking, the vehicle speed is 1.75 km/h (1 mph) or less and the parking brake is not released.
Check that the seat belt warning light (in the combination meter assembly) turns off when the passenger seat belt is fastened with the seat belt warning light (in the combination meter assembly) on or blinking.
INSPECT REAR SEAT BELT WARNING LIGHT (w/ Rear Seat Belt Warning System, w/o Occupant Detection Sensor, for Type A)
The warning lighting time differs depending on the specification, so they are listed as "Type A" and "Type B".
| *1 | Combination Meter Assembly (Rear Seat Belt Warning Light) |
| *a | LH |
| *b | Center |
| *c | RH |
Turn the ignition switch off.
Unfasten the rear seat belt.
Turn the ignition switch to ON.
Check that the rear seat belt warning light (in the combination meter assembly) turns on.
Check that the rear seat belt warning light turns on for approximately 60 seconds and then turns off.
Fasten the rear seat belt.
With the rear seat belt warning light off, check that the rear seat belt warning light in the combination meter assembly turns on again when the rear seat belt is unfastened.
INSPECT REAR SEAT BELT WARNING LIGHT (w/ Rear Seat Belt Warning System, w/o Occupant Detection Sensor, for Type B)
The warning lighting time differs depending on the specification, so they are listed as "Type A" and "Type B".
| *1 | Combination Meter Assembly (Rear Seat Belt Warning Light) |
| *a | LH |
| *b | Center |
| *c | RH |
Turn the ignition switch off.
Unfasten the rear seat belt.
Turn the ignition switch to ON.
Check that the rear seat belt warning light (in the combination meter assembly) turns on.
Check that the rear seat belt warning light turns on for approximately 66 seconds and then turns off.
Fasten the rear seat belt.
With the rear seat belt warning light off, check that the rear seat belt warning light in the combination meter assembly turns on again when the rear seat belt is unfastened.
INSPECT REAR SEAT BELT WARNING LIGHT (w/ Rear Seat Belt Warning System, w/ Occupant Detection Sensor)
Perform the following inspection for each rear seat.
| *1 | Combination Meter Assembly (Rear Seat Belt Warning Light) |
| *a | LH |
| *b | Center |
| *c | RH |
Turn the ignition switch to ON.
Place a load of 20 kg (44.1 lb) on the rear seat.
When placing the load on the rear seat, do not let it touch the seatback.
Fasten the rear seat belt.
Check that the rear seat belt warning light in the combination meter assembly turns on with the rear seat belt unfastened and under any of the following conditions.
Shift position in P.
The parking brake is not released.
Check that the rear seat belt warning light in the combination meter assembly turns off when the rear seat belt is fastened.
INSPECT DRIVER SEAT BELT WARNING BUZZER (w/ Buzzer Regulated by Law)
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Turn the ignition switch off.
Turn the ignition switch to ON.
After turning the ignition switch to ON, wait for approximately 1.8 seconds with the driver seat belt not fastened check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
After 24 seconds have passed after the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.
After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 90 seconds.
When 96 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer sounds once and then once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
INSPECT DRIVER SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law, for Type A)
The buzzer sounding time differs depending on the specification, so they are listed as "Type A" and "Type B".
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 30 seconds when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
After the buzzer has sounded intermittently at 1.2-second intervals for 30 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 90 seconds.
When 120 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
INSPECT DRIVER SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law, for Type B)
The buzzer sounding time differs depending on the specification, so they are listed as "Type A" and "Type B".
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 24 seconds when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
After the buzzer has sounded intermittently at 1.2-second intervals for 24 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 100 seconds.
When 124 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
INSPECT PASSENGER SEAT BELT WARNING BUZZER (w/ Buzzer Regulated by Law)
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Fasten the driver seat belt.
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Place a load of 20 kg (44.1 lb) on the passenger seat.
When placing the load on the passenger seat, do not let it touch the seatback.
Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
After 24 seconds have passed after the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.
After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 90 seconds.
When 96 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer sounds once and then once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
INSPECT PASSENGER SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law, for Type A)
The buzzer sounding time differs depending on the specification, so they are listed as "Type A" and "Type B".
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Fasten the driver seat belt.
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Place a load of 20 kg (44.1 lb) on the passenger seat.
When placing the load on the passenger seat, do not let it touch the seatback.
Check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 30 seconds when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
After the buzzer has sounded intermittently at 1.2-second intervals for 30 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 90 seconds.
When 120 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
INSPECT PASSENGER SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law, for Type B)
The buzzer sounding time differs depending on the specification, so they are listed as "Type A" and "Type B".
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Fasten the driver seat belt.
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Place a load of 20 kg (44.1 lb) on the passenger seat.
When placing the load on the passenger seat, do not let it touch the seatback.
Check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 24 seconds when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
After the buzzer has sounded intermittently at 1.2-second intervals for 24 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 100 seconds.
When 124 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the seat belt unfastened.
INSPECT REAR SEAT BELT WARNING BUZZER (w/ Buzzer Regulated by Law, w/ Rear Seat Belt Warning System)
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Fasten the driver seat belt.
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Ensure that the rear seat belt is fastened, and then unfasten it.
Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
After 24 seconds have passed after the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.
After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 30 seconds.
When 36 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer sounds once and then once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the rear seat belt unfastened.
INSPECT REAR SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law, w/ Rear Seat Belt Warning System, w/o Occupant Detection Sensor)
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Fasten the driver seat belt.
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Ensure that the rear seat belt is fastened, and then unfasten it.
Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
After the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.
After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 60 seconds.
When 66 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer sounds once and then once again sounds intermittently when the seat belt is fastened and then unfastened again, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the rear seat belt unfastened.
INSPECT REAR SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law, w/ Rear Seat Belt Warning System, w/ Occupant Detection Sensor, for Type A)
The buzzer sounding time differs depending on the specification, so they are listed as "Type A" and "Type B".
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Fasten the driver seat belt.
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Place a load of 20 kg (44.1 lb) on the rear seat to check.
When placing the load on the rear seat, do not let it touch the seatback.
Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
After the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 6 seconds.
After the buzzer has sounded intermittently at 1.2-second intervals for 6 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 60 seconds.
When 66 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer sounds once and then once again sounds intermittently when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the rear seat belt unfastened.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the rear seat belt unfastened.
INSPECT REAR SEAT BELT WARNING BUZZER (w/o Buzzer Regulated by Law, w/ Rear Seat Belt Warning System, w/ Occupant Detection Sensor, for Type B)
The buzzer sounding time differs depending on the specification, so they are listed as "Type A" and "Type B".
Using the GTS, check that the customization setting for the seat belt warning buzzer (in the combination meter assembly) is on.
Lift up the vehicle.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS
Fasten the driver seat belt.
Start the engine*1 or hybrid control system*2.
*1: for Gasoline Model
*2: for HV Model
Place a load of 20 kg (44.1 lb) on the rear seat to check.
When placing the load on the rear seat, do not let it touch the seatback.
Check that the seat belt warning buzzer (in the combination meter assembly) sounds once when the rear seat belt is fastened and then unfastened, and then the vehicle is driven at approximately 20 km/h (12 mph) or higher.
After the buzzer sounds once, check that the seat belt warning buzzer (in the combination meter assembly) sounds intermittently at 1.2-second intervals for 24 seconds.
After the buzzer has sounded intermittently at 1.2-second intervals for 24 seconds, check that the interval changes and the buzzer sounds intermittently at 0.4-second intervals for 100 seconds.
When 124 seconds have passed after the buzzer started sounding intermittently, check that the seat belt warning buzzer (in the combination meter assembly) stops.
After the seat belt warning buzzer (in the combination meter assembly) stops, check that the buzzer sounds once and then once again sounds intermittently when the vehicle is driven at approximately 20 km/h (12 mph) or higher with the rear seat belt unfastened.
Check that the seat belt warning buzzer (in the combination meter assembly) stops when the shift position is changed to R while the seat belt warning buzzer (in the combination meter assembly) is sounding.
Check that the buzzer once again sounds intermittently when the shift position is changed to D again and the vehicle is driven at approximately 20 km/h (12 mph) or higher with the rear seat belt unfastened.