Home › General › SPECIFICATIONS › K120F MULTIDRIVE / CVT › 2018.10–2019.09
RM3620E _V1 General _077121 SPECIFICATIONS _0379025 K120F MULTIDRIVE / CVT F

SPECIFICATIONS  K120F MULTIDRIVE / CVT  SERVICE DATA  


CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM

*1: Connect the GTS to the DLC3 when measuring the fluid pressure.

*2: Depress the accelerator pedal at a consistent angle to maintain the specified vehicle speed.

Engine stall speed D 2350 +/- 300 rpm
Fluid pressure (Throttle valve fully opened)*1
Engine stall speed
2350 +/- 300 rpm
D 3.5 to 4.3 MPa (35.7 to 43.8 kgf/cm2, 508 to 624 psi)
R 1.6 to 2.4 MPa (16.3 to 24.5 kgf/cm2, 232 to 348 psi)
Time lag N → D Less than 1.2 seconds
N → R Less than 1.5 seconds
Engine idle speed (A/C off) N 750 to 850 rpm
Shift schedule (D) (NORMAL)
Throttle valve position (100%) Fully depressed
(Before 1st up-shift)
6100 to 6900 rpm
Fully depressed
(Before 2nd up-shift)
6100 to 6900 rpm
Throttle valve position (Constant opening angle)*2 30 km/h (19 mph) 750 to 1200 rpm
70 km/h (43 mph) 1000 to 1500 rpm
100 km/h (62 mph) 1300 to 1800 rpm
Kick down Accelerator pedal fully depressed above 30 km/h (19 mph) 2500 rpm or more
Shift schedule (D) (SPORT)
Throttle valve position (100%) Fully depressed
(Before 1st up-shift)
6100 to 6900 rpm
Fully depressed
(Before 2nd up-shift)
6100 to 6900 rpm
Throttle valve position (Constant opening angle)*2 30 km/h (19 mph) 1500 to 1950 rpm
70 km/h (43 mph) 2000 to 2500 rpm
100 km/h (62 mph) 2400 to 2900 rpm
Kick down Accelerator pedal fully depressed above 30 km/h (19 mph) 2500 rpm or more
Lock-up point
Lock-up ON
(Accelerator pedal opening 5%)
D (NORMAL) 10 to 30 km/h (6 to 19 mph)
D (SPORT)
Lock-up OFF
(Accelerator pedal opening 0%)
D (NORMAL) 5 to 20 km/h (3 to 12 mph)
D (SPORT)

CONTINUOUSLY VARIABLE TRANSAXLE FLUID
Dry fill w/o Stop and Start System: 8.6 liters (9.1 US qts, 7.6 Imp. qts) Toyota Genuine CVT fluid FE
w/ Stop and Start System 8.3 liters (8.8 US qts, 7.3 Imp. qts)

CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Transaxle housing type T oil seal Standard Depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

CONTINUOUSLY VARIABLE TRANSAXLE UNIT
Input shaft sub-assembly Standard input shaft end play 0.345 to 1.357 mm (0.0136 to 0.0534 in.)
Clearance of C-1 clutch Pack clearance (Reference) 0.45 to 0.75 mm (0.0177 to 0.0295 in.)
Forward clutch flange thickness Part number Thickness (mm (in.)) Mark
35635-12280 3.3 (0.130) B
35635-12290 3.4 (0.134) C
35635-12300 3.5 (0.138) D
35635-12310 3.6 (0.142) E
35635-12320 3.7 (0.146) F
35635-12330 3.8 (0.150) G
Forward clutch return spring sub-assembly Standard free length 18.54 mm (0.730 in.)
Planetary gear assembly Standard clearance 0.16 to 0.61 mm (0.00630 to 0.0240 in.)
Clearance of No. 1 brake Pack clearance 0.539 to 1.321 mm (0.0212 to 0.0520 in.)
1st and reverse brake return spring sub-assembly Standard free length 17.56 mm (0.691 in.)
Thrust needle roller bearing and thrust bearing race diameter Mark Thrust bearing race diameter inside / outside
mm (in.)
Thrust needle roller bearing diameter inside / outside
mm (in.)
A - 47.75 (1.88) / 65.8 (2.59)
B 26.38 (1.04) / 38.9 (1.53) 24.9 (0.98) / 38.9 (1.53)
C - 29.7 (1.17) / 49.1 (1.93)
Straight pin Protrusion height 7.0 to 8.0 mm (0.276 to 0.315 in.)
Differential case tapered roller bearing preload (at 10 rpm) Standard turning torque 1.65 to 2.66 N*m (17 to 27 kgf*cm, 15 to 23 in.*lbf)
Shim thickness Part number Thickness (mm (in.)) Mark
90564-75036 1.77 (0.0697) A
90564-75037 1.80 (0.0709) B
90564-75038 1.83 (0.0720) C
90564-75039 1.86 (0.0732) D
90564-75040 1.89 (0.0744) E
90564-75041 1.92 (0.0756) F
90564-75042 1.95 (0.0768) G
90564-75043 1.98 (0.0780) H
90564-75044 2.01 (0.0791) J
90564-75045 2.04 (0.0803) K
90564-75046 2.07 (0.0815) L
90564-75047 2.07 (0.0815) M
90564-75052 2.13 (0.0839) N
90564-75053 2.16 (0.0850) P
90564-75054 2.19 (0.0862) Q
90564-75055 2.22 (0.0874) R
90564-75056 2.25 (0.0886) S
90564-75057 2.28 (0.0898) T
90564-75058 2.31 (0.0909) U
Adjust reduction driven gear tapered roller bearing preload (at 10 rpm) Standard turning torque Differential case tapered roller bearing preload + 3.21 to 6.11 N*m (33 to 62 kgf*cm, 2 to 5 ft.*lbf)
Shim thickness Part number Thickness (mm (in.)) Mark
90564-44070 1.59 (0.0626) A
90564-44071 1.62 (0.0638) B
90564-44072 1.65 (0.0650) C
90564-44073 1.68 (0.0661) D
90564-44074 1.71 (0.0673) E
90564-44075 1.74 (0.0685) F
90564-44076 1.77 (0.0697) G
90564-44077 1.80 (0.0709) H
90564-44078 1.83 (0.0720) J
90564-44079 1.86 (0.0732) K
90564-44080 1.89 (0.0744) L
90564-44081 1.92 (0.0756) M
90564-44082 1.95 (0.0768) N
90564-44083 1.98 (0.0780) P
90564-44084 2.01 (0.0791) Q
90564-44085 2.04 (0.0803) R
90564-44086 2.07 (0.0815) S
90564-44087 2.10 (0.0827) T
90564-44088 2.13 (0.0839) U
90564-44089 2.16 (0.0850) V
90564-44090 2.19 (0.0862) W
90564-44091 2.22 (0.0874) X
90564-44092 2.25 (0.0886) Y
Front drive shaft oil seal LH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Transaxle housing type T oil seal Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

TORQUE CONVERTER AND DRIVE PLATE
Drive plate runout Maximum 0.30 mm (0.0118 in.)

FRONT DIFFERENTIAL OIL SEAL (for LH Side)
Front drive shaft oil seal LH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

FRONT DIFFERENTIAL OIL SEAL (for RH Side)
Front drive shaft oil seal RH Standard depth 24.5 to 25.5 mm (0.9646 to 1.0039 in.)
Differential side oil seal Standard depth 5.5 to 6.5 mm (0.217 to 0.256 in.)

REVOLUTION SENSOR (NT SENSOR)
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
High signal 12 to 16 mA

REVOLUTION SENSOR (NOUT SENSOR)
Tester Connection Condition Specified Condition
1 (NOO) - 2 (NOB) Low signal 4 to 8 mA
High signal 12 to 16 mA

REVOLUTION SENSOR (NSS SENSOR)
Tester Connection Condition Specified Condition
1 (NSSO) - 2 (NSSB) Low signal 4 to 8 mA
High signal 12 to 16 mA

SHIFT STROKE SENSOR
Standard voltage (Combined dry-cell battery voltage of 4.5 V)
Tester Connection Condition Specified Condition
4 (VOUT) - 3 (GND) High signal 4.09 to 4.19 V
Low signal 0.36 to 0.45 V
Reference voltage (Combined dry-cell battery voltage of 5.0 V)
Tester Connection Condition Specified Condition
4 (VOUT) - 3 (GND) High signal 4.55 to 4.65 V
Low signal 0.4 to 0.5 V

PARK/NEUTRAL POSITION SWITCH
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P and N 10 kΩ or higher
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever in D, M, "+" or "-" Below 1 Ω
Shift lever not in D, M, "+" or "-" 10 kΩ or higher

SHIFT LEVER
Shift lock control ECU (w/ Smart Entry and Start System)
Wire harness
Tester Connection Condition Specified Condition
4 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
5 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
1 (E) - Body ground Always Below 1 Ω
Shift lock solenoid
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
1 (SLS+) - 2 (SLS-) Always 112 Ω
Shift lock control ECU (w/o Smart Entry and Start System)
Wire harness
Tester Connection Condition Specified Condition
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
1 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
7 (E) - Body ground Always Below 1 Ω
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
Shift lock solenoid
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
1 (SLS+) - 2 (SLS-) Always 112 Ω
Transmission control switch (for LHD)
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher
Transmission control switch (for RHD)
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher
1 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher

COMBINATION SWITCH
NORMAL mode switch:
Tester Connection Condition Specified Condition
8 (B) - 13 (GND) NORMAL mode switch being pushed and held Below 1 Ω
NORMAL mode switch not pushed 10 kΩ or higher
SPORT mode switch:
Tester Connection Condition Specified Condition
9 (P) - 13 (GND) SPORT mode switch being pushed and held Below 1 Ω
SPORT mode switch not pushed 10 kΩ or higher
ECO mode switch:
Tester Connection Condition Specified Condition
7 (ECU) - 13 (GND) ECO mode switch being pushed and held Below 1 Ω
ECO mode switch not pushed 10 kΩ or higher
SNOW mode switch:
Tester Connection Condition Specified Condition
6 (2ND) - 13 (GND) SNOW mode switch being pushed and held Below 1 Ω
SNOW mode switch not pushed 10 kΩ or higher
Illumination Illuminates:
Battery positive (+) → Terminal 12 (ILL+)
Battery negative (-) → Terminal 1 (ILL-)
Illuminates

SHIFT PADDLE SWITCH
No. 1 transmission shift switch assembly
Tester Connection Condition Specified Condition
1 (SDN) - 2 (ECC) "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher
1 (SDN) - 3 (ECC') "-" (Down shift) shift paddle switch operated and held Below 2.5 Ω
"-" (Down shift) shift paddle switch not operated 1 MΩ or higher
No. 2 transmission shift switch assembly
Tester Connection Condition Specified Condition
1 (SUP) - 2 (ECC') "+" (Up shift) shift paddle switch operated and held Below 2.5 Ω
"+" (Up shift) shift paddle switch not operated 1 MΩ or higher

VALVE BODY ASSEMBLY
Shift solenoid valve (SLG, SL1, SL2, SLU, SLP, SLS)
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω

DIFFERENTIAL CASE
Front drive shaft oil seal RH Oil seal drive in depth 24.5 to 25.5 mm (0.965 to 1.004 in.)