DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. -
There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the Freeze Frame Data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
600 to 700 rpm: Engine idling (shift lever in neutral, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Mass Air Flow Sensor | Airflow rate from mass air flow meter sub-assembly | Min.: 0 gm/sec
Max.: 655.35 gm/sec |
·
1.5 to 3.3 gm/sec: Engine idling (engine warmed up) ·
8.0 to 13.0 gm/sec: 3000 rpm (without load) |
This is the intake air amount measured by the mass air flow meter sub-assembly. |
| Intake Manifold Absolute Pressure | Intake manifold absolute pressure | Min.: 0 kPa (0 psi)
Max.: 2047.96 kPa (296.95 psi) |
·
80 to 110 kPa (11.6 to 15.95 psi): Ignition switch ON ·
18 to 38 kPa (2.6 to 5.5 psi): Engine idling with warmed up engine |
·
This is the intake manifold pressure. ·
This item is the pressure detected by the manifold absolute pressure sensor and is used for air fuel ratio control and EGR valve control.
|
| Intake Manifold Absolute Pressure Supported | Status of intake manifold absolute pressure | Unsupp or Supp | Supp | - |
| Coolant Temperature | Engine coolant temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up |
|
| Throttle Motor Duty Ratio | Throttle actuator | Min.: 0%
Max.: 100% |
0 to 22%: Engine idling with warmed up engine (A/C off and shift lever in neutral) | This is the output duty ratio of the throttle actuator drive circuit. |
| Starter SW | Starter signal | ON or OFF | ·
ON: Starter operating ·
OFF: Starter not operating |
- |
| Stop Light SW | Stop light switch status | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| NIM Sensor Speed | Input shaft speed (NIM) | Min.: 0 rpm
Max.: 16383 rpm |
Equal to engine speed (NE): Clutch pedal not depressed, vehicle being driven | - |
| NIM Sensor Voltage | Input shaft speed (NIM) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Clutch pedal not depressed, vehicle being driven | - |
| Shift SW Status (R Range) | Back-up light switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
- |
| Shift SW Status (N,P Range) | Clutch pedal switch status | ON or OFF | ·
ON: Clutch pedal fully depressed ·
OFF: Clutch pedal released |
- |
| Shift SW Status (N,P Range) Supported | Status of clutch pedal switch supported | Unsupp or Supp | Supp | - |
| Clutch Stroke Position | Clutch pedal stroke calculated by ECM | Min.: -200.0%
Max.: 199.9% |
Value increases: Clutch pedal released → clutch pedal fully depressed | - |
| Clutch Stroke Sensor Voltage | Clutch pedal stroke sensor assembly output voltage | Min.: 0.000 V
Max.: 4.999 V |
·
0.96 to 1.04 V: Clutch pedal fully released ·
Value changes progressively (Only increase): Not depressed → Fully depressed (Clutch pedal should be operated slowly) |
- |
| iMT SW | iMT switch (integration control and panel assembly) status | ON or OFF | ·
ON: iMT switch (integration control and panel assembly) being pushed ·
OFF: iMT switch (integration control and panel assembly) not being pushed |
- |
| iMT Telltale | iMT telltale display request | OFF, Green or Yellow | ·
OFF: iMT system off ·
Green: iMT system in standby ·
Yellow: iMT system malfunction, indicator light initial check |
- |