Home › Drivetrain › EG62 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076270 EG62 MANUAL TRANSMISSION / TRANSAXLE _0372178 MANUAL TRANSAXLE SYSTEM J

EG62 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  Pattern Select Switch iMT Mode Circuit  


DESCRIPTION

When the iMT switch (integration control and panel assembly) is operated to turn the iMT system on, the iMT indicator (green) in the combination meter assembly illuminates.

When the iMT indicator (green) is illuminated, the iMT system is in standby.

WIRING DIAGRAM

C290726E46
2.26,1.51 3.26,1.74 1,0.229 10 false G111 2.24,1.677 4.125,2.417 1.885,0.74 10 false iMT Switch (Integration Control and Panel Assembly) 5.927,1.844 6.385,2.042 0.458,0.198 10 false A24 5.927,1.99 6.344,2.542 0.417,0.552 10 false ECM 6.229,0.74 6.844,0.938 0.615,0.198 10 false 12 V 5.573,0.906 6.188,1.104 0.615,0.198 10 false MTMS 5.323,0.906 5.563,1.115 0.24,0.208 10 false 38 4.042,0.885 4.323,1.146 0.281,0.26 10 false 7 2.167,0.906 2.625,1.26 0.458,0.354 10 false 6 2.344,0.906 2.875,1.135 0.531,0.229 10 false GND 3.823,0.885 4.052,1.073 0.229,0.188 10 false S

PROCEDURE

1.READ VALUE USING GTS (iMT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
iMT SW iMT switch (integration control and panel assembly) status ON or OFF
·

ON: iMT switch (integration control and panel assembly) being pushed

·

OFF: iMT switch (integration control and panel assembly) not being pushed


-
Powertrain > Engine > Data List
Tester Display
iMT SW
50003 372 570

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT iMT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
2.INSPECT iMT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.
C380111C20
2.292,1.906 1.979,1.479 true 2.844,1.865 2.292,1.479 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *1 2.281,1.958 2.438,2.156 0.156,0.198 10 false S 2.74,1.896 3.156,2.104 0.417,0.208 10 false GND
*1 iMT Switch (Integration Control and Panel Assembly)


Remove the integration control and panel assembly.

Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>INTELLIGENT MANUAL TRANSMISSION SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (S) - 6 (GND) iMT switch (integration control and panel assembly) being pushed Below 1 Ω
7 (S) - 6 (GND) iMT switch (integration control and panel assembly) not being pushed 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - BODY GROUND)

NG

REPLACE iMT SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - BODY GROUND)
a.
C408783C01
0.313,0.896 0.813,1.24 0.5,0.344 1.063,1.802 1.365,1.438 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.896,1.844 1.354,2.042 0.458,0.198 10 false GND 0.385,0.99 1,1.188 0.615,0.198 10 false G111
*a Front view of wire harness connector
(to Integration Control and Panel Assembly)


Disconnect the integration control and panel assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G111-6 (GND) - Body ground Always Below 1 Ω



c.

Connect the integration control and panel assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - ECM)
a.
C408786C01
1.208,0.104 1.833,0.406 0.625,0.302 0.75,3 1.042,1.896 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.542,3.052 1.156,3.25 0.615,0.198 10 false MTMS 1.375,0.177 1.99,0.375 0.615,0.198 10 false A24
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-38 (MTMS) - Body ground iMT switch (integration control and panel assembly) being pushed Below 1 Ω
A24-38 (MTMS) - Body ground iMT switch (integration control and panel assembly) not being pushed 10 kΩ or higher



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR