Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  C13A2  Engine Switch/Power Switch Malfunction  


DESCRIPTION

When the power switch is turned on (IG), power is supplied to the parking brake ECU assembly. This DTC is stored if the IG power source is not input to the parking brake ECU assembly when communication with other ECUs occurs.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A2 Engine Switch/Power Switch Malfunction Both of the following conditions are met:
1.

Power switch on (IG)

2.

When the hybrid vehicle control ECU assembly communicates with the main body ECU (multiplex network body ECU) via CAN communication, IG power supply is not received for approximately 15 seconds.


·

Wire harness or connector

·

IG power source circuit

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C253323E14
2.156,1.198 3.292,1.438 1.135,0.24 10 false ECU-IG1 NO.3 0.771,1.01 1.885,1.198 1.115,0.188 10 false from IG Circuit 0.698,0.375 2.75,0.708 2.052,0.333 10 false CAN Communication System 4.521,1 4.781,1.177 0.26,0.177 10 false IG 4.24,0.823 4.396,0.979 0.156,0.156 10 false 5 4.458,1.542 6.927,1.854 2.469,0.313 10 false Parking Brake ECU Assembly 4.146,1.01 4.479,1.24 0.333,0.229 10 false M35 0.427,1.708 4.208,2.344 3.781,0.635 10 false Instrument Panel Junction Block Assembly 6.135,0.573 6.708,0.76 0.573,0.188 10 false M36 6.219,0.365 6.417,0.583 0.198,0.219 10 false 9 5.635,0.583 6.042,0.854 0.406,0.271 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the power switch is first turned on (IG).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE CIRCUIT - PARKING BRAKE ECU ASSEMBLY)
a.

Turn the power switch off.


b.
C306865C30
1.5,0.302 1.927,0.573 0.427,0.271 1.594,1.188 1.5,1.75 true 1.583,0.354 2.042,0.552 0.458,0.198 10 false M35 0.063,0.094 0.375,0.292 0.313,0.198 10 false *a 1.438,1.802 1.75,2 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Disconnect the parking brake ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M35-5 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Proceed to
DTC is output
DTC is not output



DTC is output

REPLACE PARKING BRAKE ECU ASSEMBLY

DTC is not output