Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster) › 2018.10–2019.09
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  C13A6  Open or Short Circuit in Motor  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A6 Open or Short Circuit in Motor One of the following conditions are met:
Detection conditions (1)
1.

Power switch on (IG) or electric parking brake switch (integration control and panel assembly) assembly pulled to lock side with power switch off.

2.

Power supply voltage and +B voltage are normal, but motor circuit is malfunctioning for approximately 1 to 2 seconds.


Detection conditions (2)

With the power switch off, an overcurrent malfunction is continuously detected for 1 second or more


Detection conditions (3)

With the power switch on (IG) and an overcurrent malfunction being continuously detected, the parking brake is locked and released 3 times


·

Wire harness or connector

·

Parking brake wire assembly

·

Parking brake actuator assembly

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Condition Combination Table: C13A6
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to lock side with power switch off ○ - - -
Power switch on (IG) - ○ - -
Power switch off - - ○ -
With the power switch on (IG) and an overcurrent malfunction being continuously detected, the parking brake is locked and released - - - ○
Malfunction Status Parking brake motor circuit malfunction when power supply voltage and +B voltage are normal ○ ○ - -
An overcurrent malfunction is continuously detected - - ○ -
Detection Time Approximately 1 to 2 seconds Approximately 1 to 2 seconds 1 second or more 3 times
Trip Count 1 trip 1 trip 1 trip 1 trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


WIRING DIAGRAM

C320708E40
1.333,0.729 1.75,0.917 0.417,0.188 10 false MRR- 1.292,1.313 1.813,1.552 0.521,0.24 10 false MRR+ 1.313,3.875 1.729,4.063 0.417,0.188 10 false MRL+ 1.333,3.292 1.75,3.479 0.417,0.188 10 false MRL- 5.354,0.719 5.896,0.969 0.542,0.25 10 false RE- 5.354,1.302 5.927,1.625 0.573,0.323 10 false RE+ 5.344,3.292 5.76,3.479 0.417,0.188 10 false LE- 5.344,3.885 5.76,4.073 0.417,0.188 10 false LE+ 3.583,0.719 4,0.906 0.417,0.188 10 false MM2 3.583,1.313 4,1.5 0.417,0.188 10 false MM2 3.594,3.292 4.01,3.479 0.417,0.188 10 false NN2 3.594,3.896 4.01,4.083 0.417,0.188 10 false NN2 4.958,0.708 5.438,0.958 0.479,0.25 10 false M49 4.958,1.302 5.458,1.594 0.5,0.292 10 false M49 4.958,3.292 5.292,3.51 0.333,0.219 10 false N57 4.969,3.885 5.375,4.135 0.406,0.25 10 false N57 1.802,0.604 1.99,0.802 0.188,0.198 10 false 3 1.802,1.198 1.99,1.396 0.188,0.198 10 false 1 1.813,3.177 2,3.375 0.188,0.198 10 false 6 1.813,3.771 2,3.969 0.188,0.198 10 false 4 0.375,4.396 0.792,4.583 0.417,0.188 10 false M36 0.573,4.573 2.792,5.042 2.219,0.469 10 false Parking Brake ECU Assembly 3.74,4.427 5.042,4.979 1.302,0.552 10 false No. 2 Parking Brake Wire Assembly 5.115,4.417 6.552,4.927 1.438,0.51 10 false Parking Brake Actuator Assembly LH 3.677,1.833 4.979,2.302 1.302,0.469 10 false No. 1 Parking Brake Wire Assembly 5.094,1.844 6.604,2.375 1.51,0.531 10 false Parking Brake Actuator Assembly RH 3.688,1.083 3.844,1.281 0.156,0.198 11 false 1 5.042,0.521 5.198,0.719 0.156,0.198 10 false 1 5.052,1.104 5.208,1.302 0.156,0.198 10 false 2 3.688,0.5 3.844,0.698 0.156,0.198 10 false 2 3.677,3.688 3.833,3.885 0.156,0.198 10 false 1 5.052,3.094 5.208,3.292 0.156,0.198 10 false 1 5.052,3.688 5.208,3.885 0.156,0.198 10 false 2 3.667,3.073 3.823,3.271 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the power switch is first turned on (IG).



PROCEDURE

1.READ VALUE USING GTS (RH ACTUATOR CURRENT STATUS / LH ACTUATOR CURRENT STATUS)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RH Actuator Current Status RH Actuator Current Status Valid or Inval Valid -
LH Actuator Current Status LH Actuator Current Status Valid or Inval Valid -
Chassis > Electric Parking Brake > Data List
Tester Display
RH Actuator Current Status
LH Actuator Current Status
50003 184 613,614
Result:
Proceed to
NEXT




NEXT

2.INSPECT PARKING BRAKE WIRE ASSEMBLY
2.INSPECT PARKING BRAKE WIRE ASSEMBLY
C408682C01
4.917,0.417 5.417,0.667 0.5,0.25 4.917,0.083 5.417,0.333 0.5,0.25 1.917,0.417 2.417,0.667 0.5,0.25 1.917,0.083 2.417,0.333 0.5,0.25 5.313,1.427 5.667,1.167 5.667,1.167 5.833,1.167 true 5,1.438 4.583,1.167 4.583,1.167 4.417,1.167 true 5,0.135 5.458,0.333 0.458,0.198 10 false M49 5.021,0.469 5.479,0.667 0.458,0.198 10 false N57 1.99,0.125 2.448,0.323 0.458,0.198 10 false MM2 2.021,0.469 2.479,0.667 0.458,0.198 10 false NN2 2.5,0.115 2.958,0.313 0.458,0.198 10 false *A 5.5,0.135 5.958,0.333 0.458,0.198 10 false *A 2.5,0.469 2.958,0.667 0.458,0.198 10 false *B 5.5,0.458 5.958,0.656 0.458,0.198 10 false *B 2.042,2.083 2.5,2.281 0.458,0.198 10 false *b 5.083,2.083 5.375,2.281 0.292,0.198 10 false *c 0.083,0.083 0.542,0.281 0.458,0.198 10 false *a 5.917,1.01 6.542,1.208 0.625,0.198 10 false RE+ *A 5.917,1.188 6.542,1.385 0.625,0.198 10 false LE+ *B 3.917,1 4.542,1.198 0.625,0.198 10 false RE- *A 3.917,1.198 4.542,1.396 0.625,0.198 10 false LE- *B
*A RH *B LH
*a Front view of Parking Brake Wire Assembly *b (to Wire Harness Connector)
*c (to Parking Brake Actuator Assembly) - -


a.

Remove the parking brake wire assembly.


b.

Check the parking brake wire assembly for damage.

OK:

No damage.


HINT:

If damaged, there may be a short in the wire harness or a short to ground.



c.

Inspect the parking brake wire assembly.

Standard Resistance:
RH
Tester Connection Condition Specified Condition
MM2-2 - M49-1 (RE-) Always Below 1 Ω
MM2-2 - M49-2 (RE+) Always 10 kΩ or higher
MM2-2 or M49-1 (RE-) - Body ground Always 10 kΩ or higher
MM2-1 - M49-2 (RE+) Always Below 1 Ω
MM2-1 - M49-1 (RE-) Always 10 kΩ or higher
MM2-1 or M49-2 (RE+) - Body ground Always 10 kΩ or higher

LH
Tester Connection Condition Specified Condition
NN2-2 - N57-1 (LE-) Always Below 1 Ω
NN2-2 - N57-2 (LE+) Always 10 kΩ or higher
NN2-2 or N57-1 (LE-) - Body ground Always 10 kΩ or higher
NN2-1 - N57-2 (LE+) Always Below 1 Ω
NN2-1 - N57-1 (LE-) Always 10 kΩ or higher
NN2-1 or N57-2 (LE+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - PARKING BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - PARKING BRAKE ACTUATOR ASSEMBLY)
a.

Turn the power switch off.


b.

Make sure the parking brake wire assembly is securely installed.


c.

Disconnect the M36 parking brake ECU assembly connector.


d.

Disconnect the M49 or N57 parking brake actuator assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
RH
Tester Connection Condition Specified Condition
M36-1 (MRR+) - M49-2 (RE+) Always Below 1 Ω
M36-3 (MRR-) - M49-1 (RE-) Always Below 1 Ω
M36-1 (MRR+) or M49-2 (RE+) - Body ground Always 10 kΩ or higher
M36-3 (MRR-) or M49-1 (RE-) - Body ground Always 10 kΩ or higher

LH
Tester Connection Condition Specified Condition
M36-4 (MRL+) - N57-2 (LE+) Always Below 1 Ω
M36-6 (MRL-) - N57-1 (LE-) Always Below 1 Ω
M36-4 (MRL+) or N57-2 (LE+) - Body ground Always 10 kΩ or higher
M36-6 (MRL-) or N57-1 (LE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY
a.

Remove the parking brake actuator assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


b.

Inspect the parking brake actuator assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY