Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  C13AD  Open in +B Circuit  


DESCRIPTION

The parking brake ECU assembly is supplied with power to operate the motor via the +B and +B2 terminals.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13AD Open in +B Circuit Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (integration control and panel assembly) pulled to lock side with power witch off.

2.

Motor +B voltage is Mid when the parking brake motor is not operating or motor +B voltage is Lo when the parking brake motor is operating for approximately 0.5 seconds or more.


HINT:

For details on the threshold value changes according to the auxiliary battery voltage value, refer to "Threshold Changes According to Auxiliary Battery Voltage".


·

Wire harness or connector

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Condition Combination Table: C13AD (Pattern 1, Pattern 2, Pattern 3, Pattern 4)
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to lock side with power switch off ○ ○ - -
Power switch on (IG) - - ○ ○
Malfunction Status Motor +B voltage is Mid when parking brake motor is not operating ○ - ○ -
Motor +B voltage is Lo when parking brake motor is operating - ○ - ○
Detection Time Approximately 0.5 seconds Approximately 0.5 seconds Approximately 0.5 seconds Approximately 0.5 seconds
Trip Count 1 trip 1 trip 1 trip 1 trip

HINT:
·

If the conditions match either of these patterns, a DTC will be output.



Threshold Changes According to Auxiliary Battery Voltage
C400815C01
0.385,0.094 0.698,0.292 0.313,0.198 10 false *a 3.844,0.083 4.156,0.281 0.313,0.198 10 false *b 0.625,0.448 0.938,0.646 0.313,0.198 10 false *e 0.635,0.698 0.948,0.896 0.313,0.198 10 false *f 0.885,1.521 1.198,1.719 0.313,0.198 10 false *d 4.344,1.531 4.656,1.729 0.313,0.198 10 false *d 4.083,0.427 4.396,0.625 0.313,0.198 10 false *e 4.104,0.688 4.417,0.885 0.313,0.198 10 false *f 2.083,2.594 2.396,2.792 0.313,0.198 10 false *c 5.531,2.594 5.844,2.792 0.313,0.198 10 false *c
*a Parking Brake Motor Not Operating *b Parking Brake Motor Operating
*c Auxiliary Battery Voltage (V) *d +B and +B2 Terminal Voltage (V)
*e Normal Range *f DTC Detection Range


WIRING DIAGRAM

C381776E03
4.552,0.573 4.708,0.771 0.156,0.198 10 false 7 4.5,1.125 4.906,1.375 0.406,0.25 10 false 12 4.833,0.719 5.198,0.958 0.365,0.24 10 false +B 4.844,1.198 5.208,1.438 0.365,0.24 10 false +B2 1.729,1.427 2.604,1.677 0.875,0.25 10 false EPB NO. 2 (*) 1.74,0.854 2.615,1.104 0.875,0.25 10 false EPB NO. 1 (*) 4.469,1.833 6.833,2.333 2.365,0.5 10 false Parking Brake ECU Assembly 4.479,1.656 4.833,1.865 0.354,0.208 10 false M36 0.333,2.292 3.177,2.656 2.844,0.365 10 false *: EPB stands for Electric Parking Brake

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the power switch is first turned on (IG).



PROCEDURE

1.READ VALUE USING GTS (RH MOTOR +B VOLTAGE / LH MOTOR +B VOLTAGE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and the GTS on.


d.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


e.

Check the Data List.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition
RH Motor +B Voltage Parking brake motor RH (parking brake actuator assembly RH) +B voltage display Lo, Mid, Error or Hi Hi
LH Motor +B Voltage Parking brake motor LH (parking brake actuator assembly LH) +B voltage display Lo, Mid, Error or Hi Hi
Chassis > Electric Parking Brake > Data List
Tester Display
RH Motor +B Voltage
LH Motor +B Voltage
50003 184 427,428

Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - AUXILIARY BATTERY)
2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - AUXILIARY BATTERY)
a.

Turn the power switch off.


b.
C307214C06
1.552,0.25 1.948,0.438 0.396,0.188 1.167,1.333 0.583,1.5 0.583,1.5 0.583,1.667 true 2.344,1.302 2.833,1.5 2.833,1.5 2.833,1.667 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.604,0.26 2.063,0.458 0.458,0.198 10 false M36 0.5,1.688 0.813,1.885 0.313,0.198 10 false +B 2.719,1.677 3.115,1.875 0.396,0.198 10 false +B2
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Disconnect the parking brake ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M36-7 (+B) - Body ground Always 11 to 14 V
M36-12 (+B2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR