Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C391864E01
2.75,0.75 2.906,0.948 0.156,0.198 10 false 5 2.74,1.448 2.896,1.646 0.156,0.198 10 false 3 0.583,1.063 1.531,1.396 0.948,0.333 10 false ECU-IG1 NO.3 3.01,0.854 3.344,1.052 0.333,0.198 10 false IG 3.01,1.573 3.49,1.792 0.479,0.219 10 false BECU 2.802,1.896 3.135,2.094 0.333,0.198 10 false M35 2.802,2.094 5.135,2.542 2.333,0.448 10 false Parking Brake ECU Assembly 5.146,1.625 7.021,2.042 1.875,0.417 10 false Combination Meter Assembly 1.865,3.438 4.042,3.667 2.177,0.229 10 false : CAN Communication Line 0.583,1.75 1.531,2.083 0.948,0.333 10 false ECU-B NO.2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the power switch is first turned on (IG).



HINT:

The condition may be that the electric parking brake is operating normally but the meter parking brake indicator light is malfunctioning.


PROCEDURE

1.VEHICLE OPERATION CHECK
a.

Turn the power switch on (READY) and move the shift lever to D. Then depress the brake pedal and pull the electric parking brake switch (integration control and panel assembly) to the lock side for 1 second. Check the parking brake indicator light condition.


b.

Release the brake pedal and check that the vehicle does not move.


c.

Depress the brake pedal and push the electric parking brake switch (integration control and panel assembly) to the release side for 1 second. Check the parking brake indicator light condition.


d.

Release the brake pedal and check that the vehicle moves.


Result:
Result Proceed to
Lock and release control is normal; parking brake indicator light is off or is blinking A
Lock and release control is malfunctioning; parking brake indicator light is illuminated or off depending on switch operation B
Lock and release control is malfunctioning; parking brake indicator light is off or is blinking C



A

2.PERFORM ACTIVE TEST USING GTS (PKB LIGHT)

B

INSPECT REAR BRAKE

C

3.CHECK HARNESS AND CONNECTOR (BECU CIRCUIT)
2.PERFORM ACTIVE TEST USING GTS (PKB LIGHT)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and the GTS on.


d.

Enter the following menus: Chassis / Electric Parking Brake / Active Test.


e.

Check the condition of the parking brake indicator light by operating the GTS.

Chassis > Electric Parking Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PKB Light Parking brake indicator light ON or OFF
·

Vehicle stopped

·

Power switch on (IG)


Chassis > Electric Parking Brake > Active Test
Tester Display
PKB Light
50004 184 29

OK:

Indicator light turns on when operating the GTS.


Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (BECU CIRCUIT)
a.

Turn the power switch off.


b.
C306865C31
1.5,0.313 1.938,0.552 0.438,0.24 1.323,1.208 1.229,1.771 true 1.583,0.344 2.042,0.542 0.458,0.198 10 false M35 0.063,0.094 0.375,0.292 0.313,0.198 10 false *a 1.031,1.823 1.573,2.021 0.542,0.198 10 false BECU
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Disconnect the parking brake ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M35-3 (BECU) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - PARKING BRAKE ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - PARKING BRAKE ECU ASSEMBLY)
a.

Turn the power switch off.


b.
C306865C32
1.5,0.313 1.948,0.531 0.448,0.219 1.667,1.198 1.813,1.76 true 1.583,0.333 2.042,0.531 0.458,0.198 10 false M35 0.063,0.094 0.375,0.292 0.313,0.198 10 false *a 1.823,1.833 2.135,2.031 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Disconnect the parking brake ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M35-5 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR