Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) D

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  FREEZE FRAME DATA  


FREEZE FRAME DATA


HINT:
·

If a DTC is output, the freeze frame data is recorded when the DTC occurs.

·

If freeze frame data is recorded when a DTC occurs, the freeze frame data is not cleared or updated until the recorded DTC is cleared.



a.

Using the GTS, the condition of the vehicle (sensors) when the system is operating or when the malfunction DTC was recorded can be checked.



Chassis > Electric Parking Brake
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RH Motor +B Voltage Parking brake motor RH (parking brake actuator assembly RH) +B voltage display Lo, Mid, Error or Hi Hi -
LH Motor +B Voltage Parking brake motor LH (parking brake actuator assembly LH) +B voltage display Lo, Mid, Error or Hi Hi -
FR Speed Sensor Open Front speed sensor RH open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
FL Speed Sensor Open Front speed sensor LH open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
RR Speed Sensor Open Rear speed sensor RH open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
RL Speed Sensor Open Rear speed sensor LH open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
EFI ECU Communication Open ECM communication open detection Normal or Error Error
·

There is no communication with ECM. As a result, "Error" is displayed permanently.

·

This item is displayed but there is no problem.


Deceleration Sensor Open Deceleration sensor (airbag sensor assembly) power supply voltage status Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
HV ECU Communication Open Hybrid vehicle control ECU assembly communication open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
Body ECU Communication Open Main body ECU (multiplex network body ECU) communication open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
Brake ECU Communication Open Skid control ECU (brake booster with master cylinder assembly) communication open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
A/C ECU Communication Open Air conditioning amplifier assembly communication open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
Navigation ECU Communication Open Radio receiver assembly communication open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
Stop and Start ECU Communication Open Engine stop and start ECU communication open detection Normal or Error Error
·

There is no communication with engine stop and start ECU. As a result, "Error" is displayed permanently.

·

This item is displayed but there is no problem.


Deceleration Sensor Open (EPB) Deceleration sensor (airbag sensor assembly) communication open detection Normal or Error Normal: Normal
Error: Momentary interruption
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
HINT:

EPB stands for electric parking brake


FR Wheel Speed Front right wheel speed display 0.0 to 326.4 km/h (0.0 to 202.8 mph) When vehicle is stopped: 0.0 km/h (0.0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
When not normal, front speed sensor RH system and CAN communication may be malfunctioning
FL Wheel Speed Front left wheel speed display 0.0 to 326.4 km/h (0.0 to 202.8 mph) When vehicle is stopped: 0.0 km/h (0.0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
When not normal, front speed sensor LH system and CAN communication may be malfunctioning
RR Wheel Speed Rear right wheel speed display 0.0 to 326.4 km/h (0.0 to 202.8 mph) When vehicle is stopped: 0.0 km/h (0.0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
When not normal, rear speed sensor RH system and CAN communication may be malfunctioning
RL Wheel Speed Rear left wheel speed display 0.0 to 326.4 km/h (0.0 to 202.8 mph) When vehicle is stopped: 0.0 km/h (0.0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
When not normal, rear speed sensor LH system and CAN communication may be malfunctioning
Deceleration Sensor 1 Deceleration sensor (airbag sensor assembly) 1 input display -18.300 to 18.318 m/s2 When vehicle is stopped: 0.000 m/s2
When driving vehicle: Continuously changes
When not normal, deceleration sensor (airbag sensor assembly) system and CAN communication may be malfunctioning
Deceleration Sensor 2 Deceleration sensor (airbag sensor assembly) 2 input display -18.300 to 18.318 m/s2 When vehicle is stopped: 0.000 m/s2
When driving vehicle: Continuously changes
When not normal, deceleration sensor (airbag sensor assembly) system and CAN communication may be malfunctioning
Forward and Rearward G Deceleration sensor (airbag sensor assembly) input display -18.300 to 18.318 m/s2 When vehicle is stopped: 0.000 m/s2
When driving vehicle: Changes according to increase or decrease in speed
When not normal, deceleration sensor (airbag sensor assembly) system and CAN communication may be malfunctioning
Zero Point of Deceleration Sensor Deceleration sensor (airbag sensor assembly) zero point display -4.595 to 4.559 m/s2 - -
Zero Point of Deceleration Sensor 2 Deceleration sensor (airbag sensor assembly) 2 zero point display -4.595 to 4.559 m/s2 - -
Vehicle Speed Vehicle speed 0.0 to 326.4 km/h (0.0 to 202.8 mph) When vehicle is stopped: 0.0 km/h (0.0 mph)
When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)
When not normal, speed sensor system and CAN communication may be malfunctioning
ECU +B1 Voltage Parking brake ECU assembly +B voltage display 0.00 to 20.00 V 11.00 to 14.00 V -
ECU +B2 Voltage Parking brake ECU assembly +B2 voltage display 0.00 to 20.00 V 11.00 to 14.00 V -
RH Actuator Motor +Terminal Voltage Parking brake motor RH (parking brake actuator assembly RH) positive (+) terminal side voltage display 0.00 to 20.00 V - -
RH Actuator Motor -Terminal Voltage Parking brake motor RH (parking brake actuator assembly RH) negative (-) terminal side voltage display 0.00 to 20.00 V - -
LH Actuator Motor +Terminal Voltage Parking brake motor LH (parking brake actuator assembly LH) positive (+) terminal side voltage display 0.00 to 20.00 V - -
LH Actuator Motor -Terminal Voltage Parking brake motor LH (parking brake actuator assembly LH) negative (-) terminal side voltage display 0.00 to 20.00 V - -
Stop Light Switch Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
EPB Switch Electric parking brake switch (integration control and panel assembly) input OFF, Lock, Release or Unknown OFF: Lock switch and release switch are off
Lock: Lock switch on
Release: Release switch on
When "Unknown" is displayed, electric parking brake switch (integration control and panel assembly) release side system may be malfunctioning
HINT:

EPB stands for electric parking brake.


Auto Mode Request Auto mode request status ON or OFF ON: Requested
OFF: Not requested
-
Shift Position Shift position information P, N, R, D or Unknown P: Shift position in P
N: Shift position in N
R: Shift position in R
D: Shift position in D
When "Unknown" is displayed, shift position signal system may be malfunctioning
IG Switch IG power source information display ON or OFF ON: IG power source is input into parking brake ECU assembly
OFF: IG power source is not input into parking brake ECU assembly
-
Lock Switch 1 Lock switch 1 input signal ON, OFF, Open or Short ON: Lock switch on
OFF: Lock switch off
When "Open" or "Short" is displayed, electric parking brake switch (integration control and panel assembly) lock side system may be malfunctioning
Lock Switch 2 Lock switch 2 input signal ON, OFF, Open or Short ON: Lock switch on
OFF: Lock switch off
When "Open" or "Short" is displayed, electric parking brake switch (integration control and panel assembly) lock side system may be malfunctioning
Release Switch 1 Release switch 1 input signal ON, OFF, Open or Short ON: Release switch on
OFF: Release switch off
When "Open" or "Short" is displayed, electric parking brake switch (integration control and panel assembly) release side system may be malfunctioning
Release Switch 2 Release switch 2 input signal ON, OFF, Open or Short ON: Release switch on
OFF: Release switch off
When "Open" or "Short" is displayed, electric parking brake switch (integration control and panel assembly) release side system may be malfunctioning
Brake Hold Ready Brake hold control permission status ON or OFF - -
Brake Hold Control Mode Brake Hold Control Mode OFF, ON, Release or EPB OFF: Brake hold control is not operating
ON: Brake hold control is operating
Release: Brake hold control is released
EPB: Parking brake is locked during brake hold control
HINT:

EPB stands for electric parking brake


EPB Lock Request Lock demand status ON or OFF ON: Requested
OFF: Not requested
HINT:

EPB stands for electric parking brake.


FR Speed Signal Status FR speed signal status Normal or Stuck Normal -
FL Speed Signal Status FL speed signal status Normal or Stuck Normal -
RR Speed Signal Status RR speed signal status Normal or Stuck Normal -
RL Speed Signal Status RL speed signal status Normal or Stuck Normal -
RH Actuator Current Status RH Actuator Current Status Valid or Inval Valid -
LH Actuator Current Status LH Actuator Current Status Valid or Inval Valid -
RH Actuator Nut Stroke Parking brake actuator assembly RH nut stroke value is displayed 0.000 to 8.160 mm (0.000 to 0.321 in.) - -
LH Actuator Nut Stroke Parking brake actuator assembly LH nut stroke value is displayed 0.000 to 8.160 mm (0.000 to 0.321 in.) - -
RH Actuator Motor Actual Current Parking brake motor RH (parking brake actuator assembly RH) current value is displayed -5.0362 to 50.5000 A - -
RH Actuator Motor Adjustment Current Parking brake motor RH (parking brake actuator assembly RH) current calibration value is displayed -6.9690 to 6.9140 A - -
RH Actuator 0 load Current Parking brake actuator assembly RH current value with no load is displayed -5.0362 to 50.5000 A - -
LH Actuator Motor Actual Current Parking brake motor LH (parking brake actuator assembly LH) current value display -5.0362 to 50.5000 A - -
LH Actuator Motor Adjustment Current Parking brake motor LH (parking brake actuator assembly LH) current calibration value display -6.9690 to 6.9140 A - -
LH Actuator 0 load Current Parking brake actuator assembly LH current value with no load is displayed -5.0362 to 50.5000 A - -
Counter of IG ON After EPB Control Cancel Number of power switch on (IG) operations after EPB control cancellation 0 to 255 Times -
HINT:

EPB stands for electric parking brake.


RH Actuator Status Parking brake actuator assembly RH condition details are displayed Default, Lock, Lock Dynamic, Release, Lock Faulty, Unexpected, Lock Standby, Release Standby, Lock Dynamic Standby, Release Dynamic Standby, Lock Dynamic Faulty, Lock Standard Control, Lock Dynamic Control, Lock Control for Prevention Loosen by High Temperature, Lock Control for Prevention Slipping Down, Re-Lock Control by Switch, Recovery Lock Control, Lock Control After Dynamic PKB, Release Standard Control, Release Dynamic Control, Full Release Control - -
LH Actuator Status Parking brake actuator assembly LH condition details are displayed Default, Lock, Lock Dynamic, Release, Lock Faulty, Unexpected, Lock Standby, Release Standby, Lock Dynamic Standby, Release Dynamic Standby, Lock Dynamic Faulty, Lock Standard Control, Lock Dynamic Control, Lock Control for Prevention Loosen by High Temperature, Lock Control for Prevention Slipping Down, Re-Lock Control by Switch, Recovery Lock Control, Lock Control After Dynamic PKB, Release Standard Control, Release Dynamic Control, Full Release Control - -
RH Actuator Motor Current Differential RH Actuator Motor Current Differential is displayed -1.008 to 0.945 A - -
LH Actuator Motor Current Differential LH Actuator Motor Current Differential is displayed -1.008 to 0.945 A - -
Detailed Freeze DTC Stored DTC INF code 0 to 65535 - Displays DTC INF code
RH Actuator Motor Gradient Current Parking brake motor RH (parking brake actuator assembly RH) current gradient display -5.0362 to 50.5000 A - -
LH Actuator Motor Gradient Current Parking brake motor LH (parking brake actuator assembly LH) current gradient display -5.0362 to 50.5000 A - -
RH Actuator Motor Relay1 Parking brake motor relay 1 RH condition details are displayed ON or OFF ON: Relay on
OFF: Relay off
-
RH Actuator Motor Relay2 Parking brake motor relay 2 RH condition details are displayed ON or OFF ON: Relay on
OFF: Relay off
-
RH Actuator Motor Relay3 Parking brake motor relay 3 RH condition details are displayed ON or OFF ON: Relay on
OFF: Relay off
-
RH Actuator Motor Relay4 Parking brake motor relay 4 RH condition details are displayed ON or OFF ON: Relay on
OFF: Relay off
-
LH Actuator Motor Relay1 Parking brake motor relay 1 LH condition details are displayed ON or OFF ON: Relay on
OFF: Relay off
-
LH Actuator Motor Relay2 Parking brake motor relay 2 LH condition details are displayed ON or OFF ON: Relay on
OFF: Relay off
-
LH Actuator Motor Relay3 Parking brake motor relay 3 LH condition details are displayed ON or OFF ON: Relay on
OFF: Relay off
-
LH Actuator Motor Relay4 Parking brake motor relay 4 LH condition details are displayed ON or OFF ON: Relay on
OFF: Relay off
-
Pull Up Resistor LCK 1 pull up resistance change input information is displayed ON or OFF - -
RH Actuator Motor Current High Parking brake motor RH (parking brake actuator assembly RH) overcurrent condition display ON or OFF OFF -
RH Actuator Motor Driver Operation Status RH Actuator Motor Driver Operation Status is displayed OK or NG - -
LH Actuator Motor Current High Parking brake motor LH (parking brake actuator assembly LH) overcurrent condition display ON or OFF OFF -
LH Actuator Motor Driver Operation Status LH Actuator Motor Driver Operation Status is displayed OK or NG - -