Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379311 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/ Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/ Vacuum Brake Booster)  U007488  Control Module Communication Bus "B" Off Bus Off  U010087  Lost Communication with ECM/PCM "A" Missing Message  U010187  Lost Communication with TCM Missing Message  U012587  Lost Communication With Multi-axis Acceleration Sensor Module Missing Message  U012687  Lost Communication with Steering Angle Sensor Module Missing Message  U013187  Lost Communication With Power Steering Control Module Missing Message  U014087  Lost Communication with Body Control Module Missing Message  U015187  Lost Communication with Restraints Control Module Missing Message  


DESCRIPTION

The skid control ECU (brake actuator assembly) communicates with the following ECUs and sensors via CAN communication.

·

ECM

·

TCM (ECM)

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Steering sensor

·

Power steering ECU (rack and pinion power steering gear assembly)

·

Main body ECU (multiplex network body ECU)

·

Airbag sensor assembly


DTC No. Detection Item DTC Detection Condition Trouble Area
U007488 Control Module Communication Bus "B" Off Bus Off The +BS terminal voltage is between 9.6 and a 16.5 V and a bus OFF state occurs for 0.1 seconds or more. CAN communication system
U010087 Lost Communication with ECM/PCM "A" Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the ECM for 2 seconds or more.
·

CAN communication system

·

ECM

·

Skid control ECU (brake actuator assembly)


U010187 Lost Communication with TCM Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the TCM (ECM) for 2 seconds or more.
·

CAN communication system

·

TCM (ECM)

·

Skid control ECU (brake actuator assembly)


U012587 Lost Communication With Multi-axis Acceleration Sensor Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the yaw rate and acceleration sensor (airbag sensor assembly) cannot be received for 1 second or more.
·

CAN communication system

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake actuator assembly)


U012687 Lost Communication with Steering Angle Sensor Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the steering sensor cannot be received for 1 second or more.
·

CAN communication system

·

Steering sensor

·

Skid control ECU (brake actuator assembly)


U013187 Lost Communication With Power Steering Control Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the power steering ECU (rack and pinion power steering gear assembly) cannot be received for 2 second or more.
·

CAN communication system

·

Power steering ECU (rack and pinion power steering gear assembly)

·

Skid control ECU (brake actuator assembly)


U014087 Lost Communication with Body Control Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, data cannot be received from main body ECU (multiplex network body ECU) continuously for 2 seconds or more.
·

CAN communication system

·

Main body ECU (multiplex network body ECU)

·

Skid control ECU (brake actuator assembly)


U015187 Lost Communication with Restraints Control Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the airbag sensor assembly cannot be received for 5 seconds or more.
·

CAN communication system

·

Airbag sensor assembly

·

Skid control ECU (brake actuator assembly)



PROCEDURE

1.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Operate the GTS to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Clear DTCs
50002 435

d.

Press the DTC clear button.


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON.


g.

Enter the following menus: System Select / Health Check.


h.

Check for DTCs.

Result:
Result Proceed to
DTCs for related systems are output together with DTC U007488, U010087, U010187, U012587, U012687, U013187, U014087 or U015187. A
U007488, U010087, U010187, U012587, U012687, U013187, U014087 or U015187 is output. B
DTCs are not output. C




A

GO TO DIAGNOSTIC TROUBLE CODE CHART (RELATED SYSTEM)

B

C