Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0372181 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P050031  Vehicle Speed Sensor "A" No Signal  


DESCRIPTION

Vehicles which are equipped with ABS (Anti-lock Brake System) detect the vehicle speed using the skid control ECU (brake actuator assembly) and wheel speed sensors. Each wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signals into a 4-pulse signal and transmits it to the TCM via the combination meter assembly. The TCM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



C398676E01
0.417,1.24 1.573,1.792 1.156,0.552 10 false from Wheel Speed Sensors 1.844,1.844 3,2.396 1.156,0.552 10 false Skid Control ECU 3.719,1.833 4.875,2.385 1.156,0.552 10 false Combination Meter Assembly 6.083,1.844 6.667,2.26 0.583,0.417 10 false TCM 3.083,0.583 4.156,0.781 1.073,0.198 10 false 4-Pulse 5.01,0.583 6.083,0.781 1.073,0.198 10 false 4-Pulse

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P050031 Vehicle Speed Sensor "A" No Signal When the speed indicated by transmission revolution sensor (NOUT) and (NSS) are 380 rpm or more, no vehicle speed sensor signal is received by the TCM for 5 seconds or more (1-trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

TCM


Comes on DTC stored SAE Code:
P0500

MONITOR DESCRIPTION

If no speed signal is received from the combination meter assembly even though the TCM determines that the vehicle is being driven, the TCM interprets this as a malfunction in the speed signal circuit. The TCM then illuminates the MIL and stores this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P050031.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A371909

Strictly observe posted speed, limits, traffic laws and road conditions.

·

Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.

·

Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.


·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.



NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

Read freeze frame data using the GTS. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Drive the vehicle and check whether the operation of the speedometer is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the diagnostic procedure for a malfunction of the speedometer.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List / Vehicle Speed.

Powertrain > Transmission > Data List
Tester Display
Vehicle Speed
50003 373 212

e.

Drive the vehicle.


f.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
·

The vehicle speed is detected using the wheel speed sensors.

-

There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.




OK:

The values displayed on the GTS and speedometer are equal.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
a.

Disconnect the G18 combination meter assembly connector.


b.

Disconnect the C33 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-36 (+S) - C33-42 (SPD) Always Below 1 Ω



d.

Connect the C33 TCM connector.


e.

Connect the G18 combination meter assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK METER / GAUGE SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK METER / GAUGE SYSTEM
a.

Proceed to Speed Signal Circuit in Meter/Gauge System.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

4.CONFIRM MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle at 24 km/h (15 mph) or more.


i.

Enter the following menus: Powertrain / Transmission / Trouble Codes.


j.

Read the DTCs.

Powertrain > Transmission > Trouble Codes
50001 373
HINT:

If no DTCs (including pending DTCs) are output, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END